Lattice Boltzmann - Langevin simulations of binary mixtures

We report a hybrid numerical method for the solution of the model H fluctuating hydrodynamic equations for binary mixtures. The momentum conservation equations with Landau-Lifshitz stresses are solved using the fluctuating lattice Boltzmann equation while the order parameter conservation equation with Langevin fluxes are solved using the stochastic method of lines. Two methods, based on finite difference and finite volume, are proposed for spatial discretisation of the order parameter equation. Special care is taken to ensure that the fluctuation-dissipation theorem is maintained at the lattice level in both cases. The methods are benchmarked by comparing static and dynamic correlations and excellent agreement is found between analytical and numerical results. The Galilean invariance of the model is tested and found to be satisfactory. Thermally induced capillary fluctuations of the interface are captured accurately, indicating that the model can be used to study nonlinear fluctuations

Electrically-driven phase transition in magnetite nanostructures

Magnetite (Fe$_{3}$O$_{4}$), an archetypal transition metal oxide, has been used for thousands of years, from lodestones in primitive compasses[1] to a candidate material for magnetoelectronic devices.[2] In 1939 Verwey[3] found that bulk magnetite undergoes a transition at T$_{V}$ $\approx$ 120 K from a high temperature "bad metal" conducting phase to a low-temperature insulating phase. He suggested[4] that high temperature conduction is via the fluctuating and correlated valences of the octahedral iron atoms, and that the transition is the onset of charge ordering upon cooling. The Verwey transition mechanism and the question of charge ordering remain highly controversial.[5-11] Here we show that magnetite nanocrystals and single-crystal thin films exhibit an electrically driven phase transition below the Verwey temperature. The signature of this transition is the onset of sharp conductance switching in high electric fields, hysteretic in voltage. We demonstrate that this transition is not due to local heating, but instead is due to the breakdown of the correlated insulating state when driven out of equilibrium by electrical bias. We anticipate that further studies of this newly observed transition and its low-temperature conducting phase will shed light on how charge ordering and vibrational degrees of freedom determine the ground state of this important compound.Comment: 17 pages, 4 figure

Are Meaningful Use Stage 2 certified EHRs ready for interoperability? Findings from the SMART C-CDA Collaborative

Background and objective Upgrades to electronic health record (EHR) systems scheduled to be introduced in the USA in 2014 will advance document interoperability between care providers. Specifically, the second stage of the federal incentive program for EHR adoption, known as Meaningful Use, requires use of the Consolidated Clinical Document Architecture (C-CDA) for document exchange. In an effort to examine and improve C-CDA based exchange, the SMART (Substitutable Medical Applications and Reusable Technology) C-CDA Collaborative brought together a group of certified EHR and other health information technology vendors. Materials and methods We examined the machine-readable content of collected samples for semantic correctness and consistency. This included parsing with the open-source BlueButton.js tool, testing with a validator used in EHR certification, scoring with an automated open-source tool, and manual inspection. We also conducted group and individual review sessions with participating vendors to understand their interpretation of C-CDA specifications and requirements. Results: We contacted 107 health information technology organizations and collected 91 C-CDA sample documents from 21 distinct technologies. Manual and automated document inspection led to 615 observations of errors and data expression variation across represented technologies. Based upon our analysis and vendor discussions, we identified 11 specific areas that represent relevant barriers to the interoperability of C-CDA documents. Conclusions: We identified errors and permissible heterogeneity in C-CDA documents that will limit semantic interoperability. Our findings also point to several practical opportunities to improve C-CDA document quality and exchange in the coming years

Supervised Hashing for Retrieval of Multimodal Biometric Data

Biometric systems commonly utilize multi-biometric approaches where a person is verified or identified based on multiple biometric traits. However, requiring systems that are deployed usually require verification or identification from a large number of enrolled candidates. These are possible only if there are efficient methods that retrieve relevant candidates in a multi-biometric system. To solve this problem, we analyze the use of hashing techniques that are available for obtaining retrieval. We specifically based on our analysis recommend the use of supervised hashing techniques over deep learned features as a possible common technique to solve this problem. Our investigation includes a comparison of some of the supervised and unsupervised methods viz. Principal Component Analysis (PCA), Locality Sensitive Hashing (LSH), Locality-sensitive binary codes from shift-invariant kernels (SKLSH), Iterative quantization: A procrustean approach to learning binary codes (ITQ), Binary Reconstructive Embedding (BRE) and Minimum loss hashing (MLH) that represent the prevalent classes of such systems and we present our analysis for the following biometric data: Face, Iris, and Fingerprint for a number of standard datasets. The main technical contributions through this work are as follows: (a) Proposing Siamese network based deep learned feature extraction method (b) Analysis of common feature extraction techniques for multiple biometrics as to a reduced feature space representation (c) Advocating the use of supervised hashing for obtaining a compact feature representation across different biometrics traits. (d) Analysis of the performance of deep representations against shallow representations in a practical reduced feature representation framework. Through experimentation with multiple biometrics traits, feature representations, and hashing techniques, we can conclude that current deep learned features when retrieved using supervised hashing can be a standard pipeline adopted for most unimodal and multimodal biometric identification tasks.</p

Studies on Performance Enhancement of Infrared and Terahertz Detectors for Space Applications

Currently, the concept of multipurpose spacecrafts is being transformed into many small spacecrafts each of them performing specific tasks and thus leading to the realization of pico and nano satellites. No matter what is the application or size, demand for more number of IR channels for earth observation is ever increasing which necessitates significant reduction in the mass, power requirement and cost of the IR detectors. In this scenario, several order of magnitude mass and power savings associated with uncooled IR arrays are advantageous compared to cooled photon detectors. However the poor speed of response of uncooled microbolometer array devices obstruct the total replacement of cooled detectors in thermal imaging applications. This is especially true when the mission requires 50 m to 100 m ground resolution, in which even the "fastest" micro bolometer arrays turns "too slow" to follow the ground trace when looked from low earth orbit (LEO). Hence there is a great and unfulfilled requirement of faster uncooled detector arrays for meeting the demand for future micro and mini satellite projects for advanced missions. The present thesis describes the systematic studies carried out in development of high performance IR and THz detectors for space applications. Ge-Si-O thin films are prepared by ion beam sputtering technique with argon (Ar) alone and argon and oxygen as sputtering species, using sputtering targets of different compositions of Ge and SiO2. The deposited thin films are amorphous in nature and have chemical compositions close to that of the target. The study of electrical properties has shown that the activation energy and hence the thermistor constant (β) and electrical resistivity (ρ) are sensitive to oxygen flow rate, and they are the least for thin films prepared with Ar alone as the sputtering species. Different thermal isolation structures (TIS), consisting of silicon nitride (Si3N4) membrane of different thicknesses, Ge-Si-O thin film and, chromium coating on the rear side of the membrane, are prepared by bulk micro-machining technique, whose thermal conductance (Gth) properties are evaluated from the experimentally determined current-voltage (I-V) characteristics. Gth shows non-linear dependence with respect to raise in temperature of thin film thermistor due to Joule heating. The infrared micro-bolometer detectors, fabricated using one of the TIS structures have shown responsivity (<v) close to 115 V W−1 at a bias voltage of 1.5 V and chopping frequency of 10 Hz, thermal time constant (τth) of 2.5 ms and noise voltage of 255 nV Hz−1⁄2 against the corresponding thermal properties of Gth and thermal capacitance Cth equal to 9.0 × 10−5 W K−1 and 1.95 × 10−7 J K−1 respectively. The detectors are found to have uniform spectral response in the infrared region from 2 µm to 20 µm, and NEDT in the range from 108 mK to 574 mK when used with an F/1 optical system. The detector, in an infrared earth sensor system, is tested before an extended black body which simulates the earth disc in the laboratory and the results are discussed. As an extension of the single element detector to array device, design of a microbolometer array for earth sensor dispensing of scanning mechanisms is presented. It makes use of four microbolometer arrays with in-line staggered configuration that stare at the earth horizons, perceiving IR radiation in the spectral band of 14 µm to 16 µm. Design of the microbolometer has been carried out keeping in mind low power, lightweight, without compromising on the performance. An array configuration of 16 × 2 pixels is designed and developed for this purpose. Finite elemental analysis is carried out for design optimization to yield best thermal properties and thus high performance of the detectors. Suitable optical design configuration was arrived to image the earth horizon on to array. Using this optimum design, prototype arrays have been fabricated, packaged and tested in front of the black body radiation source and found to have Responsivity, NEP, and D∗ of 120 V W−1, 5.0 W Hz−1⁄2, 1.10 × 107 cm Hz1⁄2 W−1 respectively. The pixels show a uniform response within a spread of ±6 % and the pixel resistances are within a range of ±5 %. Optically Immersed Bolometer IR detectors are fabricated using electron beam evaporated Vanadium Oxide as the sensing material. Spin coated polyimide is used as medium to optically immerse the sensing element to the flat surface of a hemispherical germanium lens. This optical immersion layer also serves as the thermal impedance control layer and decides the performance of the devices in terms of responsivity and noise parameters. The devices have been packaged in suitable electro-optical packages and the detector parameters are studied in detail. Thermal time constant varies from 0.57 ms to 6.1 ms and responsivity from 75VW−1 to 757VW−1 corresponding to polyimide thickness in the range 2.0 μm to 70 μm for a detector bias of 9V. Highest D obtained was 1.28 × 108 cm Hz1⁄2W−1. Noise Equivalent Temperature Difference (NETD) of 20mK is achieved for devices with polyimide thickness of 32 μm, whereas the NETD × th product is the lowest for devices with moderate thickness of thermal impedance layer. Bolometric THz detectors were fabricated using V2O5 as sensing element immersed onto germanium hemispherical lens using polyimide as immersion media. These detectors were characterized for their efficiency in detection of THz radiation in the range 10 THz to 35 THz emitted by a black body radiator. The responsivity of the devices determined in four different frequency bands covering the spectrum of interest and a maximum responsivity of 398VW−1 was observed. A variation in the responsivity is observed which is due to the characteristics absorption of polyimide in the THz region of interest and can be avoided by replacing with HDPE which has less attenuation. NEP of 6.8 × 10−10WHz−1⁄2 was observed which is very close to the state of art in the case of uncooled detectors which entitles the detectors for spectroscopic applications. Specific Detectivity D* was observed to be much higher than the conventional detectors thanks to the benefits of immersion. NETD of 26mK was observed which is advantageous of application of these detectors in imaging applications These studies have lead to development of a new technology for fabrication of high performance IR and THz detectors which can be used for spectroscopic and imaging applications. Further, this technology can be scaled for development of linear and area arrays finding applications where the speed of respnose as well as sensitivity are of equal importance. from 0.57 ms to 6.1 ms and responsivity from 75 V W−1 to 757 V W−1 corresponding to polyimide thickness in the range 2.0 µm to 70 µm for a detector bias of 9 V. Highest D∗ obtained was 1.28 × 108 cm Hz1⁄2 W−1. Noise Equivalent Temperature Difference (NETD) of 20 mK is achieved for devices with polyimide thickness of 32 µm, whereas the NETD × τth product is the lowest for devices with moderate thickness of thermal impedance layer. Bolometric THz detectors were fabricated using V2O5 as sensing element immersed onto germanium hemispherical lens using polyimide as immersion media. These detectors were characterized for their efficiency in detection of THz radiation in the range 10 THz to 35 THz emitted by a black body radiator. The responsivity of the devices determined in four different frequency bands covering the spectrum of interest and a maximum responsivity of 398 V W−1 was observed. A variation in the responsivity is observed which is due to the characteristics absorption of polyimide in the THz region of interest and can be avoided by replacing with HDPE which has less attenuation. NEP of 6.8 × 10−10 W Hz−1⁄2 was observed which is very close to the state of art in the case of uncooled detectors which entitles the detectors for spectroscopic applications. Specific Detectivity D* was observed to be much higher than the conventional detectors thanks to the benefits of immersion. NETD of 26 mK was observed which is advantageous of application of these detectors in imaging applications These studies have lead to development of a new technology for fabrication of high performance IR and THz detectors which can be used for spectroscopic and imaging applications. Further, this technology can be scaled for development of linear and area arrays finding applications where the speed of respnose as well as sensitivity are of equal importance

REMOTE TRACKING OF ANDROID SMARTPHONES

The Purpose of the paper is to trace out the status and progress of the employee mobile and the relevant information is transferred to the mobile of the project manager and updated in the web server. The employee’s problem related to the company can be monitored by the project manager and he can also track the employee’s current location through the GPS. In existing system, the CBI alone can trace the mobile phone of any person with the help of unique IMEI number in telephone exchange. So there is no possibility to trace any information regarding the employee’s mobile details by the project manager. So to overcome, this system was implemented

Pressure simulation for footstep energy harvesting paver

Amongst all the energy sources from human motion, footstep has the potential of producing electrical energy as an alternative source to non-conventional renewable energy. Researchers have shown that human footstep kinetic energy can be converted to electrical energy by devised mechanism for low power application such as powering lights, radio and charging phones. Eventually, a novel fluid based energy harvesting paver was developed and tested to contribute towards sustainable development. The paver uses mini hydro generators to produce energy as fluid is forced through these mini hydro generators upon human stepping. This paper presents the pressure simulation of fluid bag system when subjected to an applied human force and the quarter ellipsoid shaped proved to be the best performer which can produce upto 1.4J per step. The pressure simulation provides a relation between pressure and output power

Drought tolerance in MnSOD transgenic Hevea brasiliensis in a dry sub-humid environment

One year old bud-grafted plants of MnSOD transgenic Hevea lines (L1 and L2) and an untransformed line of clone RRII 105 were used in the present study to evaluate their physiological performance in a dry sub-humid environment by withholding irrigation and to assess the recovery by re-watering. The dry matter partitioning was more towards the root in transgenic lines (55% and 60% in Ll and L2, respectively) but, was less in the untransformed RRII 105 (43%). After six days of moisture stress in polybags, pre-dawn leaf water potential and relative water content declined in all the lines, however, transgenic line L1 showed higher tissue water content throughout the drought as well as recovery period. Chlorophyll content did not show any significant reduction. Net photosynthetic rate (PN) declined rapidly and it reached near zero on the third day of drought imposition except for line L1, which showed lesser decline in PN. The decline in stomatal conductance (gs) was more rapid than PN in all the lines. On re-watering, recovery of PN and gs was better in the transgenic lines than untransformed RRII 105, which did not recover fully from the drought impact. Antioxidant enzymes, superoxide dismutase and peroxidase did not show a definite trend in their activities in these lines. However, it was found that the transgenic line L1 had better drought tolerant capacity in terms of lesser inhibition of photosynthetic rate under drought and faster recovery on re-watering

Drought tolerance in MnSOD transgenic Hevea brasiliensis in a dry sub-humid environment

One year old bud-grafted plants of MnSOD transgenic Hevea lines (L1 and L2) and an untransformed line of clone RRII 105 were used in the present study to evaluate their physiological performance in a dry sub-humid environment by withholding irrigation and to assess the recovery by re-watering. The dry matter partitioning was more towards the root in transgenic lines (55% and 60% in Ll and L2, respectively) but, was less in the untransformed RRII 105 (43%). After six days of moisture stress in polybags, pre-dawn leaf water potential and relative water content declined in all the lines, however, transgenic line L1 showed higher tissue water content throughout the drought as well as recovery period. Chlorophyll content did not show any significant reduction. Net photosynthetic rate (PN) declined rapidly and it reached near zero on the third day of drought imposition except for line L1, which showed lesser decline in PN. The decline in stomatal conductance (gs) was more rapid than PN in all the lines. On re-watering, recovery of PN and gs was better in the transgenic lines than untransformed RRII 105, which did not recover fully from the drought impact. Antioxidant enzymes, superoxide dismutase and peroxidase did not show a definite trend in their activities in these lines. However, it was found that the transgenic line L1 had better drought tolerant capacity in terms of lesser inhibition of photosynthetic rate under drought and faster recovery on re-watering