Acquisition and preliminary analysis of multi-channel seismic reflection data, acquired during the oceanographic cruises of the TOMO-ETNA experiment

The TOMO-ETNA experiment was performed in the framework of the FP7 “MED-SUV” (MEDiterranean SUpersite Volcanoes) in order to gain a detailed geological and structural model of the continental and oceanic crust concerning Etna and Aeolian Islands volcanoes (Sicily, Italy), by means of active and passive seismic exploration methodologies. Among all data collected, some 1410 km of marine multi-channel seismic (MCS) reflection profiles were acquired in the Ionian and Tyrrhenian Seas during two of the three oceanographic cruises of the TOMO-ETNA experiment, in July and November 2014, with the aim of shading light to deep, intermediate and shallow stratigraphy and crustal structure of the two above mentioned areas. The MCS sections, targeted to deep exploration, were acquired during the oceanographic cruise on board of the R/V “Sarmiento de Gamboa”, using an active seismic source of 16 air-guns, for a total volume of 4340 cu. in., and a 3000 m long, 240-channels digital streamer as receiving system. High-resolution seismic profiles were instead collected through the R/V “Aegaeo”, using two smaller air-guns (overall 270 cu. in. volume) and a 96 channels, 300 m long digital streamer. This paper provides a detailed description of the acquisition parameters and main processing steps adopted for the MCS data. Some processed lines are shown and preliminarily interpreted, to highlight the overall good quality and the high potential of the MCS sections collected during the TOMO-ETNA experiment. © 2016 by the Istituto Nazionale di Geofisica e Vulcanologia. All rights reserved

Natural Polymers and Cosmeceuticals for a Healthy and Circular Life: The Examples of Chitin, Chitosan, and Lignin

The present review considers the design and introduction of new cosmeceuticals in the market, based on natural polymers and active molecules extracted from biomass, in a biomimetic strategy, starting with a consideration of the biochemical mechanisms, followed by natural precision biopolymer production. After introducing the contest of nanobiotechnology in relationship with its applicability for skin contact products and classifying the currently available sustainable polymers, some widely selected abundant biopolymers (chitin, chitosan, and lignin), showing specific functionalities (anti-microbial, anti-oxidant, anti-inflammatory, etc.), are described, especially considering the possibility to combine them in nanostructured tissues, powders, and coatings for producing new cosmeceuticals, but with potentialities in other sectors, such as biomedical, personal care, and packaging sectors. After observing the general increase in market wellness and beauty forecasts over the next few years, parallelisms between nano and macro scales have suggested that nanobiotechnology application expresses the necessity to follow a better way of producing, selecting, and consuming goods that will help to transform the actual linear economy in a circular economy, based on redesigning, reducing, recycling, and reusing

Evaluation of mechanical and interfacial properties of bio-composites based on poly(lactic acid) with natural cellulose fibers

The circular economy policy and the interest for sustainable material are inducing a constant expansion of the bio-composites market. The opportunity of using natural fibers in bio-based and biodegradable polymeric matrices, derived from industrial and/or agricultural waste, represents a stimulating challenge in the replacement of traditional composites based on fossil sources. The coupling of bioplastics with natural fibers in order to lower costs and promote degradability is one of the primary objectives of research, above all in the packaging and agricultural sectors where large amounts of non-recyclable plastics are generated, inducing a serious problem for plastic disposal and potential accumulation in the environment. Among biopolymers, poly(lactic acid) (PLA) is one of the most used compostable, bio-based polymeric matrices, since it exhibits process ability and mechanical properties compatible with a wide range of applications. In this study, two types of cellulosic fibers were processed with PLA in order to obtain bio-composites with different percentages of microfibers (5%, 10%, 20%). The mechanical properties were evaluated (tensile and impact test), and analytical models were applied in order to estimate the adhesion between matrix and fibers and to predict the material's stiffness. Understanding these properties is of particular importance in order to be able to tune and project the final characteristics of bio-composites

Pullulan for advanced sustainable body- And skin-contact applications

The present review had the aim of describing the methodologies of synthesis and properties of biobased pullulan, a microbial polysaccharide investigated in the last decade because of its interesting potentialities in several applications. After describing the implications of pullulan in nano-technology, biodegradation, compatibility with body and skin, and sustainability, the current applications of pullulan are described, with the aim of assessing the potentialities of this biopolymer in the biomedical, personal care, and cosmetic sector, especially in applications in contact with skin

The evolution of the Sciara del Fuoco subaerial slope during the 2007 Stromboli eruption: Relation between deformation processes and effusive activity

Focusing on the Island of Stromboli, this research investigates whether airborne remote sensing systems, such as those based on digital photogrammetry and laser scanner sensors, can be adopted to monitor slope deformation and lava emplacement processes in active volcanic areas. Thanks to the capability of extracting accurate topographic data and working on flexible time schedules, these methods can be used to constrain the regular and more frequent measurements derived from satellite observations. This work is dedicated to the monitoring of Stromboli's volcanic edifice which is beneficial when obtaining quantitative data on the geometry of deformation features and the displaced (failures and landslides) and emplaced (lava flows) volumes. In particular, we focus on the capability of extracting average effusion rates from volume measurements that can be used to validate or integrate satellite-derived estimates. Since 2001, a number of airborne remote sensing surveys, namely Digital Photogrammetry (DP) and Airborne Laser Scanning (ALS), have been carried out on Stromboli's volcano to obtain high resolution Digital Elevation Models (DEM) and orthophotos with sub-meter spatial resolution and a time schedule suitable for monitoring the morphological evolution of the surface during the quiescent phases. During the last two effusive eruptions (2002–2003 and 2007) the surface modifications, created on the Sciara del Fuoco slope and on the crater area as a consequence of effusive activity, were quantified and monitored using the same methodologies. Thiswork, which is based on the results obtained from the multi-temporal quantitative analysis of the data collected from 2001 to 2007, mainly focuses on the 2007 eruption but also accounts for analogies and differences regarding the 2002–2003 event. The 2007 eruption on the Sciara del Fuoco slope from 27 February until 2 April, produced a compound lava field including a lava delta on the shoreline, discharging most of the lava into the sea. The comparison of the 2007 DEMs with a pre-eruption surface (2006 LIDAR survey) allowed for the evaluation of the total lava volume that accumulated on the subaerial slope while two syn-eruption DEMs were used to calculate the average effusion rates during the eruption. Since the evolution of a lava field produced during an eruption can be seen as a proxy for the magma intrusion mechanism, hypotheses are formulated on the connection between the lava discharge and the instabilities suffered by the slope

The marine activities performed within the TOMO-ETNA experiment

The TOMO-ETNA experiment was planned in order to obtain a detailed geological and structural model of the continental and oceanic crust beneath Mt. Etna volcano and northeastern Sicily up to the Aeolian Islands (southern Italy), by integrating data from active and passive refraction and reflection seismic methodologies, magnetic and gravity surveys. This paper focuses on the marine activities performed within the experiment, which have been carried out in the Ionian and Tyrrhenian Seas, during three multidisciplinary oceanographic cruises, involving three research vessels (\u201cSarmiento de Gamboa\u201d, \u201cGalatea\u201d and \u201cAegaeo\u201d) belonging to different countries and institutions. During the offshore surveys about 9700 air-gun shots were produced to achieve a high-resolution seismic tomography through the wide-angle seismic refraction method, covering a total of nearly 2650 km of shooting tracks. To register ground motion, 27 ocean bottom seismometers were deployed, extending the inland seismic permanent network of the Istituto Nazionale di Geofisica e Vulcanologia (INGV) and a temporary network installed for the experiment. A total of 1410 km of multi-channel seismic reflection profiles were acquired to image the subsurface of the area and to achieve a 2D velocity model for each profile. Multibeam sonar and sub bottom profiler data were also collected. Moreover, a total of 2020 km of magnetic and 680 km of gravity track lines were acquired to compile magnetic and gravity anomaly maps offshore Mt. Etna volcano. Here, high-resolution images of the seafloor, as well as sediment and rock samples, were also collected using a remotely operated vehicle

Chitin and Its Derivatives: Nanostructured Materials from Different Marine and Terrestrial Sources

Chitin is a very abundant polysaccharide that can be obtained from well-known marine sources (crustaceans), but also from terrestrial sources (mushrooms and insects). In the case where animal sources are considered, the material can be obtained by much abundant food or feeding waste. The extraction methodologies were not developed with similar technical readiness levels considering the different sources and the further conversion to chitin nanofibrils and chitosan is also under study, enabling the production of products differentiated for their macromolecular structures and morphology.Chitin nanofibrils from sea food sources were used in sanitary, cosmetic and packaging applications, where their anti-microbial properties and good biocompatibility were very useful. Chitin from mushrooms and sea food was used as starting material in possible coatings for cellulosic and bioplastic substrates. Currently chitin from insects (Hermetia Illucens) is also under study as well as the methodologies for extracting derivatives from it. Infrared analysis is an interesting technique to compare chitins, chitin nanofibrils and chitosan from different sources as well as electron microscopy for studying their morphology. The derivatives of chitin, such as chitosan and chitin nanofibrils, show anti-microbial properties. Hence, their use in several applications, ranging from packaging to sanitary and cosmetics, can conjugate high performance novel products with a reduced environmental concern. The comparison between chitin derivatives from different sources is very useful to address the biopolymers to specific applications, including the agricultural sector. While more and more applications for chitin derivatives will be developed, differences between them should be clarified and correlated to the sources, the methodologies of their production and their physical-chemical properties

A comprehensive characterization of Hermetia illucens derived chitosan produced through homogeneous deacetylation

The increasing demand for chitin and chitosan is driving research to explore alternative sources to crustaceans. Insects, particularly bioconverters as Hermetia illucens, are promising substitutes as they process food industry waste into valuable molecules, including chitin. Chitosan can be produced by chitin deacetylation: hot deacetylation to obtain a heterogeneous chitosan, the commonly produced, and cold deacetylation to obtain a homogeneous chitosan, not widely available. The two different treatments lead to a different arrangement of the amine and acetyl groups in the chitosan structure, affecting its molecular weight, deacetylation degree, and biological activity. This is the first report on the production and chemical-physical and biological characterization of homogenous chitosan derived from H. illucens larvae, pupal exuviae, and adults. This work, in addition to the report on heterogeneous chitosan by our research group, completes the overview of H. illucens chitosan. The yield values obtained for homogeneous chitosan from pupal exuviae (3 and 7 %) are in the range of insect (2–8 %) and crustaceans (4–15 %) chitosan. The evaluation of the antioxidant activity and antimicrobial properties against Gram-negative (Escherichia coli) and Gram-positive (Micrococcus flavus) bacteria confirmed the great versatility of H. illucens chitosan for biomedical and industrial applications and its suitability as an alternative source to crustaceans

Electrosprayed Chitin Nanofibril/Electrospun Polyhydroxyalkanoate Fiber Mesh as Functional Nonwoven for Skin Application

Polyhydroxyalkanoates (PHAs) are a family of bio-based polyesters that have found different biomedical applications. Chitin and lignin, byproducts of fishery and plant biomass, show antimicrobial and anti-inflammatory activity on the nanoscale. Due to their polarities, chitin nanofibril (CN) and nanolignin (NL) can be assembled into micro-complexes, which can be loaded with bioactive factors, such as the glycyrrhetinic acid (GA) and CN-NL/GA (CLA) complexes, and can be used to decorate polymer surfaces. This study aims to develop completely bio-based and bioactive meshes intended for wound healing. Poly(3-hydroxybutyrate)/Poly(3-hydroxyoctanoate-co-3-hydroxydecanoate), P(3HB)/P(3HO-co-3HD) was used to produce films and fiber meshes, to be surface-modified via electrospraying of CN or CLA to reach a uniform distribution. P(3HB)/P(3HO-co-3HD) fibers with desirable size and morphology were successfully prepared and functionalized with CN and CLA using electrospinning and tested in vitro with human keratinocytes. The presence of CN and CLA improved the indirect antimicrobial and anti-inflammatory activity of the electrospun fiber meshes by downregulating the expression of the most important pro-inflammatory cytokines and upregulating human defensin 2 expression. This natural and eco-sustainable mesh is promising in wound healing applications