Low temperature specific heat of vanadium carbide

Low temperature specific heat measurements on vanadium carbide crystal

Superconducting magnesium diboride films on Silicon with Tc0 about 24K grown via vacuum annealing from stoichiometric precursors

Superconducting magnesium diboride films with Tc0 ~ 24 K and sharp transition \~ 1 K were successfully prepared on silicon substrates by pulsed laser deposition from a stoichiometric MgB2 target. Contrary to previous reports, anneals at 630 degree and a background of 2x10^(-4) torr Ar/4%H2 were performed without the requirement of Mg vapor or an Mg cap layer. This integration of superconducting MgB2 films on silicon may thus prove enabling in superconductor-semiconductor device applications. Images of surface morphology and cross-section profiles by scanning electron microscopy (SEM) show that the films have a uniform surface morphology and thickness. Energy dispersive spectroscopy (EDS) reveals these films were contaminated with oxygen, originating either from the growth environment or from sample exposure to air. The oxygen contamination may account for the low Tc for those in-situ annealed films, while the use of Si as the substrate does not result in a decrease in Tc as compared to other substrates.Comment: 5 pages, 4 figures, 15 references; due to file size limit, images were blure

An improved continuous compositional-spread technique based on pulsed-laser deposition and applicable to large substrate areas

A new method for continuous compositional-spread (CCS) thin-film fabrication based on pulsed-laser deposition (PLD) is introduced. This approach is based on a translation of the substrate heater and the synchronized firing of the excimer laser, with the deposition occurring through a slit-shaped aperture. Alloying is achieved during film growth (possible at elevated temperature) by the repeated sequential deposition of sub-monolayer amounts. Our approach overcomes serious shortcomings in previous in-situ implementations of CCS based on sputtering or PLD, in particular the variations of thickness across the compositional spread and the differing deposition energetics as function of position. While moving-shutter techniques are appropriate for PLD-approaches yielding complete spreads on small substrates (i.e. small as compared to distances over which the deposition parameters in PLD vary, typically about 1 cm), our method can be used to fabricate samples that are large enough for individual compositions to be analyzed by conventional techniques, including temperature-dependent measurements of resistivity and dielectric and magnetic and properties (i.e. SQUID magnetometry). Initial results are shown for spreads of (Sr,Ca)RuO$_3$.Comment: 6 pages, 8 figures, accepted for publication in Rev. Sci. Instru

Observed Effects of a Changing Step-Edge Density on Thin-Film Growth Dynamics

We grew SrTiO3 on SrTiO3 [001] by pulsed laser deposition, while observing x-ray diffraction at the (0 0 .5) position. The drop dI in the x-ray intensity following a laser pulse contains information about plume-surface interactions. Kinematic theory predicts dI/I = -4sigma(1-sigma), so that dI/I depends only on the amount of deposited material sigma. In contrast, we observed experimentally that |dI/I| < 4sigma(1-sigma), and that dI/I depends on the phase of x-ray growth oscillations. The combined results suggest a fast smoothing mechanism that depends on surface step-edge density.Comment: 4 figure

Effective Vortex Pinning in MgB2 thin films

We discuss pinning properties of MgB2 thin films grown by pulsed-laser deposition (PLD) and by electron-beam (EB) evaporation. Two mechanisms are identified that contribute most effectively to the pinning of vortices in randomly oriented films. The EB process produces low defected crystallites with small grain size providing enhanced pinning at grain boundaries without degradation of Tc. The PLD process produces films with structural disorder on a scale less that the coherence length that further improves pinning, but also depresses Tc

On the de Haas-van Alphen effect in inhomogeneous alloys

We show that Landau level broadening in alloys occurs naturally as a consequence of random variations in the local quasiparticle density, without the need to consider a relaxation time. This approach predicts Lorentzian-broadened Landau levels similar to those derived by Dingle using the relaxation-time approximation. However, rather than being determined by a finite relaxation time $\tau$, the Landau-level widths instead depend directly on the rate at which the de Haas-van Alphen frequency changes with alloy composition. The results are in good agreement with recent data from three very different alloy systems.Comment: 5 pages, no figure

Strongly Enhanced Current Densities in Superconducting Coated Conductors of YBa2Cu3O7-x + BaZrO3

There are numerous potential applications for superconducting tapes, based on YBa2Cu3O7-x (YBCO) films coated onto metallic substrates. A long established goal of more than 15 years has been to understand the magnetic flux pinning mechanisms which allow films to maintain high current densities out to high magnetic fields. In fact, films carry 1-2 orders of magnitude higher current densities than any other form of the material. For this reason, the idea of further improving pinning has received little attention. Now that commercialisation of conductors is much closer, for both better performance and lower fabrication costs, an important goal is to achieve enhanced pinning in a practical way. In this work, we demonstrate a simple and industrially scaleable route which yields a 1.5 to 5-fold improvement in the in-field current densities of already-high-quality conductors

Interpreting planners' talk about change: An exploratory study.

Talk by planners about major changes (‘reform’) in a particular planning regime is the focus of this article. Change in planning in the United Kingdom has been a recurrent theme in planning practice and research. However, there is little looking at practitioners both in the public and the private sectors in relation to change. Also, theory development has been limited and the interpretive link between institutional change, organisational change and planners’ situated agency could be strengthened. This article aims to add new dimensions to the current debate by looking at planners in both the public and the private sectors in Wales; by adopting a more open-ended approach requiring planners to generate ideas and display a perspective on planning; and by linking theories of institutional and organisational change with the model of actors’ agency developed by Bevir and Rhodes to form an interpretive frame. With reflections stemming from an exploratory case in Wales, the article seeks also to contribute to debates on planning in the United Kingdom and beyond, reaching to new-institutionalist theory and interpretive ontologie

Hyperthermal Pulsed-Laser Ablation Beams for Film Deposition and Surface Microstructural Engineering

This paper presents an overview of pulsed-laser ablation for film deposition and surface microstructure formation. By changing the ambient gas pressure from high vacuum to several Torr (several hundred Pa) and by selecting the pulsed-laser wavelength, the kinetic energy of ablated atoms/ions can be varied from several hundred eV down to {approximately}0.1 eV and films ranging from superhard to nanocrystalline may be deposited. Furthermore, cumulative (multi-pulse) irradiation of a semiconductor surface (e.g. silicon) in an oxidizing gas (0{sub 2}, SF{sub 6}) et atmospheric pressure can produce dense, self-organized arrays of high-aspect-ratio microcolumns or microcones. Thus, a wide range of materials synthesis and processing opportunities result from the hyperthermal flux and reactive growth conditions provided by pulsed-laser ablation