Suspended liquid particle disturbance on laser-induced blast wave and low density distribution

The impurity effect of suspended liquid particles on the laser-induced gas breakdown was experimentally investigated in quiescent gas. The focus of this study is the investigation of the influence of the impurities on the shock wave structure as well as the low density distribution. A 532 nm Nd:YAG laser beam with an 188 mJ/pulse was focused on the chamber filled with suspended liquid particles 0.9 ± 0.63 μm in diameter. Several shock waves are generated by multiple gas breakdowns along the beam path in the breakdown with particles. Four types of shock wave structures can be observed: (1) the dual blast waves with a similar shock radius, (2) the dual blast waves with a large shock radius at the lower breakdown, (3) the dual blast waves with a large shock radius at the upper breakdown, and (4) the triple blast waves. The independent blast waves interact with each other and enhance the shock strength behind the shock front in the lateral direction. The triple blast waves lead to the strongest shock wave in all cases. The shock wave front that propagates toward the opposite laser focal spot impinges on one another, and thereafter a transmitted shock wave (TSW) appears. The TSW interacts with the low density core called a kernel; the kernel then longitudinally expands quickly due to a Richtmyer-Meshkov-like instability. The laser-particle interaction causes an increase in the kernel volume which is approximately five times as large as that in the gas breakdown without particles. In addition, the laser-particle interaction can improve the laser energy efficiency

Compressible flow structures interaction with a two-dimensional ejector: a cold-flow study

An experimental study has been conducted to examine the interaction of compressible flow structures such as shocks and vortices with a two-dimensional ejector geometry using a shock-tube facility. Three diaphragm pressure ratios ofP4 =P1 = 4, 8, and 12 have been employed, whereP4 is the driver gas pressure andP1 is the pressure within the driven compartment of the shock tube. These lead to incident shock Mach numbers of Ms = 1:34, 1.54, and 1.66, respectively. The length of the driver section of the shock tube was 700 mm. Air was used for both the driver and driven gases. High-speed shadowgraphy was employed to visualize the induced flowfield. Pressure measurements were taken at different locations along the test section to study theflow quantitatively. The induced flow is unsteady and dependent on the degree of compressibility of the initial shock wave generated by the rupture of the diaphragm

Influence of composition and precipitation evolution on damage at grain boundaries in a crept polycrystalline Ni-based superalloy

© 2018 Acta Materialia Inc. The microstructural and compositional evolution of intergranular carbides and borides prior to and after creep deformation at 850 °C in a polycrystalline nickel-based superalloy was studied. Primary MC carbides, enveloped within intergranular γ′ layers, decomposed resulting in the formation of layers of the undesirable η phase. These layers have a composition corresponding to Ni3Ta as measured by atom probe tomography and their structure is consistent with the D024 hexagonal structure as revealed by transmission electron microscopy. Electron backscattered diffraction reveals that they assume various misorientations with regard to the adjacent grains. As a consequence, these layers act as brittle recrystallized zones and crack initiation sites. The composition of the MC carbides after creep was altered substantially, with the Ta content decreasing and the Hf and Zr contents increasing, suggesting a beneficial effect of Hf and Zr additions on the stability of MC carbides. By contrast, M5B3 borides were found to be microstructurally stable after creep and without substantial compositional changes. Borides at 850 °C were found to coarsen, resulting in some cases into γ′- depleted zones, where, however, no cracks were observed. The major consequences of secondary phases on the microstructural stability of superalloys during the design of new polycrystalline superalloys are discussed

Quantification challenges for atom probe tomography of hydrogen and deuterium in zircaloy-4

Analysis and understanding of the role of hydrogen in metals is a significant challenge for the future of materials science, and this is a clear objective of recent work in the atom probe tomography (APT) community. Isotopic marking by deuteration has often been proposed as the preferred route to enable quantification of hydrogen by APT. Zircaloy-4 was charged electrochemically with hydrogen and deuterium under the same conditions to form large hydrides and deuterides. Our results from a Zr hydride and a Zr deuteride highlight the challenges associated with accurate quantification of hydrogen and deuterium, in particular associated with the overlap of peaks at a low mass-to-charge ratio and of hydrogen/deuterium containing molecular ions. We discuss possible ways to ensure that appropriate information is extracted from APT analysis of hydrogen in zirconium alloy systems that are important for nuclear power applications

Experimental investigations of compressible vortex loops

The present study involves the shock wave and consequent vortex loop generated when a shock tube with various nozzle geometries is employed. It aims to provide quantitative and qualitative insight into the physics of these compressible phenomena. The geometries included two elliptic nozzles with minor to major axis ratios of 0.4 and 0.6, a 15 mm circular nozzle and a 30×30 mm<sup>2</sup> square nozzle. The experiments were performed for driver gas (air) pressures of 4, 8 and 12 bars. Schlieren, shadowgraphy, and particle image velocimetry techniques were employed to visualize and quantify the induced flow field