Specimen size and geometry effects on fracture toughness of Al2O3 measured with short rod and short bar chevron-notch specimens

Plane strain fracture toughness measurements were made on Al2O3 using short rod and short bar chevron notch specimens previously calibrated by the authors for their dimensionless stress intensity factor coefficients. The measured toughness varied systematically with variations in specimen size, proportions, and chevron notch angle apparently due to their influence on the amount of crack extension to maximum load (the measurement point). The toughness variations are explained in terms of a suspected rising R curve for the material tested, along with a discussion of an unavoidable imprecision in the calculation of K sub Ic for materials with rising R curves when tested with chevron notch specimens

Fracture toughness of brittle materials determined with chevron notch specimens

The use of chevron-notch specimens for determining the plane strain fracture toughness (K sub Ic) of brittle materials is discussed. Three chevron-notch specimens were investigated: short bar, short rod, and four-point-bend. The dimensionless stress intensity coefficient used in computing K sub Ic is derived for the short bar specimen from the superposition of ligament-dependent and ligament-independent solutions for the straight through crack, and also from experimental compliance calibrations. Coefficients for the four-point-bend specimen were developed by the same superposition procedure, and with additional refinement using the slice model of Bluhm. Short rod specimen stress intensity coefficients were determined only by experimental compliance calibration. Performance of the three chevron-notch specimens and their stress intensity factor relations were evaluated by tests on hot-pressed silicon nitride and sintered aluminum oxide. Results obtained with the short bar and the four-point-bend specimens on silicon nitride are in good agreement and relatively free of specimen geometry and size effects within the range investigated. Results on aluminum oxide were affected by specimen size and chevron-notch geometry, believed due to a rising crack growth resistance curve for the material. Only the results for the short bar specimen are presented in detail

The effect of (Ti + Al): V ratio on the structure and oxidation behaviour of TiAlN/VN nano-scale multilayer coatings

Nano-scaled multilayered TiAlN/VN coatings have been grown on stainless steel and M2 high speed steel substrates at U-B = - 85 V in an industrial, four target, Hauzer HTC 1000 coater using combined cathodic steered arc etching/unbalanced magnetron sputtering. X-ray diffraction (XRD) has been used to investigate the effects of process parameters (Target Power) on texture evolution (using texture parameter T*), development of residual stress (sin(2) psi method) and nano-scale multilayer period. The composition of the coating was determined using energy dispersive X-ray analysis. The thermal behaviour of the coatings in air was studied using thermo-gravimetric analysis, XRD and scanning electron microscopy. The bi-layer period varied between 2.8 and 3.1 nm and in all cases a {1 1 0} texture developed with a maximum value T* = 4.9. The residual stress varied between -5.2 and -7.4 GPa. The onset of rapid oxidation occurred between 628 and 645 degreesC depending on the (Ti+Al):V ratio. After oxidation in air at 550 degreesC AlVO4, TiO2 and V2O5 Phases were identified by XRD with the AlVO4, TiO2 being the major phases. The formation of AlVO4 appears to disrupt the formation of Al2O3 which imparts oxidation resistance to TiAlN based coatings. Increasing the temperature to 600 and 640 degreesC led to a dramatic increase in the formation of V2O5 which was highly oriented (0 0 1) with a plate-like morphology. At 640 degreesC there was no evidence of the coating on XRD. Increasing the temperature to 670 degreesC led to further formation of AlVO4 and a dramatic reduction in V2O5. (C) 2003 Elsevier B.V. All rights reserved

Smoothed Particle Magnetohydrodynamics III. Multidimensional tests and the div B = 0 constraint

In two previous papers (Price & Monaghan 2004a,b) (papers I,II) we have described an algorithm for solving the equations of Magnetohydrodynamics (MHD) using the Smoothed Particle Hydrodynamics (SPH) method. The algorithm uses dissipative terms in order to capture shocks and has been tested on a wide range of one dimensional problems in both adiabatic and isothermal MHD. In this paper we investigate multidimensional aspects of the algorithm, refining many of the aspects considered in papers I and II and paying particular attention to the code's ability to maintain the div B = 0 constraint associated with the magnetic field. In particular we implement a hyperbolic divergence cleaning method recently proposed by Dedner et al. (2002) in combination with the consistent formulation of the MHD equations in the presence of non-zero magnetic divergence derived in papers I and II. Various projection methods for maintaining the divergence-free condition are also examined. Finally the algorithm is tested against a wide range of multidimensional problems used to test recent grid-based MHD codes. A particular finding of these tests is that in SPMHD the magnitude of the divergence error is dependent on the number of neighbours used to calculate a particle's properties and only weakly dependent on the total number of particles. Whilst many improvements could still be made to the algorithm, our results suggest that the method is ripe for application to problems of current theoretical interest, such as that of star formation.Comment: Here is the latest offering in my quest for a decent SPMHD algorithm. 26 pages, 15 figures, accepted for publication in MNRAS. Version with high res figures available from http://www.astro.ex.ac.uk/people/dprice/pubs/spmhd/spmhdpaper3.pd

Observation of the Crab Nebula Gamma-Ray Emission Above 220 Gev by the Cat Cherenkov Imaging Telescope

The CAT imaging telescope, recently built on the site of the former solar plant Themis (French Pyrenees), observed gamma-rays from the Crab nebula from October 1996 to March 1997. This steady source, often considered as the standard candle of very-high-energy gamma-ray astronomy, is used as a test-beam to probe the performances of the new telescope, particularly its energy threshold (220 GeV at 20 degrees zenith angle) and the stability of its response. Due to the fine-grain camera, an accurate analysis of the longitudinal profiles of shower images is performed, yielding the source position in two dimensions for each individual shower.Comment: 5 pages, 3 figures, Tex, contribution to 25th ICRC Durba

Contact Strength and Fracture Toughness from Opposite Cylinder Loading Tests

Bars loaded by oppositely concentrated forces via rollers are appropriate test specimens for the determination of strength and fracture toughness under contact loading. Test devices are described and solutions for the stress, the stress intensity factor, and the T-stress term are reported. Experimental results are compiled for the contact strength. For most investigated materials, measured contact strengths showed strongly reduced Weibull exponents compared with those from 4-point bending tests. This important effect is attributed to the strong stress gradients near the contact zone