Diamond thin Film Detectors for Beam Monitoring Devices

Diamonds offer radiation hard sensors, which can be used directly in primary beams. Here we report on the use of a polycrystalline CVD diamond strip sensor as beam monitor of heavy ion beams with up to 2.10^9 lead ions per bunch. The strips allow for a determination of the transverse beam profile to a fraction of the pitch of the strips, while the timing information yields the longitudinal bunch length with a resolution of the order of a few mm.Comment: 6 pages, 7 figures, to appear in the Proceedings of the Hasselt Diamond Workshop (Hasselt, Belgium, Feb. 2006), v4: accidentally submitted figure, appearing at end, remove

Performance of the CMS Cathode Strip Chambers with Cosmic Rays

The Cathode Strip Chambers (CSCs) constitute the primary muon tracking device in the CMS endcaps. Their performance has been evaluated using data taken during a cosmic ray run in fall 2008. Measured noise levels are low, with the number of noisy channels well below 1%. Coordinate resolution was measured for all types of chambers, and fall in the range 47 microns to 243 microns. The efficiencies for local charged track triggers, for hit and for segments reconstruction were measured, and are above 99%. The timing resolution per layer is approximately 5 ns

Performance and Operation of the CMS Electromagnetic Calorimeter

The operation and general performance of the CMS electromagnetic calorimeter using cosmic-ray muons are described. These muons were recorded after the closure of the CMS detector in late 2008. The calorimeter is made of lead tungstate crystals and the overall status of the 75848 channels corresponding to the barrel and endcap detectors is reported. The stability of crucial operational parameters, such as high voltage, temperature and electronic noise, is summarised and the performance of the light monitoring system is presented

Development of Diamond Tracking Detectors for High Luminosity Experiments at LHC

During 2006 detectors based on new polycrystalline CVD (pCVD) material were produced as candidates for use in LHC experiments. The first full size diamond pixel module with ATLAS specifications using a $2 \times 6$ cm$^2$ pCVD sample was characterized in the 2006 CERN test beam. Radiation damage studies performed outside of CERN corroborate the radiation hardness of this material. Radiation hardness studies at CERN using the highest quality diamond were deferred until 2007 due to the PS magnet problem. ATLAS, CMS, ALICE and LHCb are planning to use diamond for their beam conditions monitoring systems. Construction of the BCM system for ATLAS was completed in 2006 and the BCM modules were characterized in 2006 CERN test beams. Similar devices are under construction for the CMS, ALICE and LHCb experiments. Single-crystal CVD (scCVD) samples were produced and made available to RD42 institutes. The first scCVD diamond pixel device was constructed and tested in the 2006 CERN test beams. In this report we present the progress and work done by the RD42 collaboration on the development of CVD diamond material for radiation detectors

Performance studies of the CMS strip tracker before installation

Peer reviewe

Integration of the End Cap TEC+ of the CMS Silicon Strip Tracker

The silicon strip tracker of the CMS experiment has been completed and inserted into the CMS detector in late 2007. The largest sub-system of the tracker is its end cap system, comprising two large end caps (TEC) each containing 3200 silicon strip modules. To ease construction, the end caps feature a modular design: groups of about 20 silicon modules are placed on sub-assemblies called petals and these self-contained elements are then mounted into the TEC support structures. Each end cap consists of 144 petals, and the insertion of these petals into the end cap structure is referred to as TEC integration. The two end caps were integrated independently in Aachen (TEC+) and at CERN (TEC--). This note deals with the integration of TEC+, describing procedures for end cap integration and for quality control during testing of integrated sections of the end cap and presenting results from the testing

CMS physics technical design report : Addendum on high density QCD with heavy ions

Peer reviewe

Reception Test of Petals for the End Cap TEC+ of the CMS Silicon Strip Tracker

The silicon strip tracker of the CMS experiment has been completed and was inserted into the CMS detector in late 2007. The largest sub system of the tracker are its end caps, comprising two large end caps (TEC) each containing 3200 silicon strip modules. To ease construction, the end caps feature a modular design: groups of about 20 silicon modules are placed on sub-assemblies called petals and these self-contained elements are then mounted onto the TEC support structures. Each end cap consists of 144 such petals, which were built and fully qualified by several institutes across Europe. Fro

Identification and Filtering of Uncharacteristic Noise in the CMS Hadron Calorimeter

VertaisarvioitupeerReviewe