Who Gets What from International Organizations? The Case of the International Atomic Energy Agency’s Technical Cooperation

What affects the allocation of aid by international organizations to their member states? Using data on nuclear assistance by the International Atomic Energy Agency (IAEA), I demonstrate that political considerations affect the likelihood of receiving aid, and the amount of aid countries receive. Specifically, I find that membership in the IAEA Board of Governors or acceptance of tougher IAEA inspections increase the likelihood of IAEA assistance, and in some cases the amounts of assistance, but only for countries that do not share policy preferences with the US. This finding is consistent with theories that foreign aid is given in exchange for cooperation and concessions to recipients that are not likely to be cooperative without aid. I also examine whether nuclear assistance is given to countries that need it the most and that can make effective use of this aid, and find only partial support for need-based explanations of aid allocation

Natural radionuclide of Po210 in the edible seafood affected by coal-fired power plant industry in Kapar coastal area of Malaysia

<p>Abstract</p> <p>Background</p> <p>Po²¹⁰can be accumulated in various environmental materials, including marine organisms, and contributes to the dose of natural radiation in seafood. The concentration of this radionuclide in the marine environment can be influenced by the operation of a coal burning power plant but existing studies regarding this issue are not well documented. Therefore, the aim of this study was to estimate the Po²¹⁰concentration level in marine organisms from the coastal area of Kapar, Malaysia which is very near to a coal burning power plant station and to assess its impact on seafood consumers.</p> <p>Methods</p> <p>Concentration of Po²¹⁰was determined in the edible muscle of seafood and water from the coastal area of Kapar, Malaysia using radiochemical separation and the Alpha Spectrometry technique.</p> <p>Results</p> <p>The activities of Po²¹⁰in the dissolved phase of water samples ranged between 0.51 ± 0.21 and 0.71 ± 0.24 mBql^-1whereas the particulate phase registered a range of 50.34 ± 11.40 to 72.07 ± 21.20 Bqkg^-1. The ranges of Po²¹⁰activities in the organism samples were 4.4 ± 0.12 to 6.4 ± 0.95 Bqkg^-1dry wt in fish (<it>Arius maculatus</it>), 45.7 ± 0.86 to 54.4 ± 1.58 Bqkg^-1dry wt in shrimp (<it>Penaeus merguiensis</it>) and 104.3 ± 3.44 to 293.8 ± 10.04 Bqkg^-1dry wt in cockle (<it>Anadara granosa</it>). The variation of Po²¹⁰in organisms is dependent on the mode of their life style, ambient water concentration and seasonal changes. The concentration factors calculated for fish and molluscs were higher than the recommended values by the IAEA. An assessment of daily intake and received dose due to the consumption of seafood was also carried out and found to be 2083.85 mBqday^-1person^-1and 249.30 μSvyr^-1respectively. These values are comparatively higher than reported values in other countries. Moreover, the transformation of Po²¹⁰in the human body was calculated and revealed that a considerable amount of Po²¹⁰can be absorbed in the internal organs. The calculated values of life time mortality and morbidity cancer risks were 24.8 × 10^-4and 34 × 10^-4respectively which also exceeded the recommended limits set by the ICRP.</p> <p>Conclusions</p> <p>The findings of this present study can be used to evaluate the safety dose uptake level of seafood as well as to monitor environmental health. However, as the calculated dose and cancer risks were found to cross the limit of safety, finding a realistic way to moderate the risk is imperative.</p

Pb-210 and Po-210 atmospheric releases via fly ash from oil shale fired power plants

WOS: 000395360900026PubMed ID: 28062225During high temperature processes in the furnace volatile and semi-volatile elements and radionuclides are partially emitted to the environment, depending on their chemical form in the original fuel, the technological set-up of the combustion system, and the prevailing combustion conditions. Two of the world's largest oil shale-fired power plants (PPs) have been operational in Estonia from the 1960s, during which time creation of significant environmental emissions and waste containing naturally occurring radionuclides has occurred. Pb-210 and Po-210 are considered natural radionuclides with the highest emission rates from PPs and possess elevated potential radiation exposure risks to humans and the environment. These radionuclides have the highest activity concentration values in fine ash fractions, especially in fractions remaining below 2.5 gm. To determine the activity concentrations of Pb-210 and Po-210 in the PPs' outlet, sampling was conducted from boilers operating on pulverized fuel (PF) technology with novel integrated desulphurization (NID) system and bag filters as well as with electrostatic precipitators (ESPs). The Pb-210 and Po-210 activity concentrations remained around 300 Bq kg(-1) for the NID system compared to 60-80 Bq kg(-1) in the ESP system. The dominant ash fraction in both systems was PM2.5, constituting over 50% of the fly ash mass collected from the outlet. The authors estimate that the total atmospherically emitted activity for the modernized PPs remains dominantly below 1% of the activity that is inserted via fuel. The implementation of higher efficiency purifications systems has significantly reduced the negative effect of these PPs. Based on annually emitted fly ash and boilers' working hours, the Pb-210 and Po-210 activity released relative to energy production were up to 68.3 kBq GWh(el)(-1) for Pb-210 and 64.6 kBq GWh(el)(-1) for Po-210. These values are 1 to 2 orders of magnitude lower compared to the situation in the 1980s. These findings represent the first publicly available quantitative results estimating the Po-210 emissions from large oil shale-fired PPs. (C) 2016 Elsevier Ltd. All rights reserved.Environmental Investment Centre [9888]; Estonian Research CouncilEesti Teadusfond (ETF) [ETF9304]The authors acknowledge the support from the Environmental Investment Centre through the project number 9888. The authors would like express their gratitude to Kaja Orupold from the Estonian University of Life Sciences for her assistance and cooperation. We also acknowledge the support from Estonian Research Council award ETF9304

Colonisation and mass rearing: learning from others

<p>Abstract</p> <p>Mosquitoes, just as other insects produced for the sterile insect technique (SIT), are subjected to several unnatural processes including laboratory colonisation and large-scale factory production. After these processes, sterile male mosquitoes must perform the natural task of locating and mating with wild females. Therefore, the colonisation and production processes must preserve characters necessary for these functions. Fortunately, in contrast to natural selection which favours a suite of characteristics that improve overall fitness, colonisation and production practices for SIT strive to maximize only the few qualities that are necessary to effectively control populations.</p> <p>However, there is considerable uncertainty about some of the appropriate characteristics due to the lack of data. Development of biological products for other applications suggest that it is possible to identify and modify competitiveness characteristics in order to produce competitive mass produced sterile mosquitoes. This goal has been pursued - and sometimes achieved - by mosquito colonisation, production, and studies that have linked these characteristics to field performance. Parallels are drawn to studies in other insect SIT programmes and aquaculture which serve as vital technical reference points for mass-production of mosquitoes, most of whose development occurs - and characteristics of which are determined - in an aquatic environment. Poorly understood areas that require further study are numerous: diet, mass handling and genetic and physiological factors that influence mating competitiveness. Compromises in such traits due to demands to increase numbers or reduce costs, should be carefully considered in light of the desired field performance.</p