The influence of clearance on friction, lubrication and squeaking in large diameter metal-on-metal hip replacements

Large diameter metal-on-metal bearings (MOM) are becoming increasingly popular, addressing the needs of young and more active patients. Clinical data has shown excellent short-to-mid-term results, though incidences of transient squeaking have been noted between implantation and up to 2 years post-operative. Geometric design features, such as clearance, have been significant in influencing the performance of the bearings. Sets of MOM bearings with different clearances were investigated in this study using a hip friction simulator to examine the influence of clearance on friction, lubrication and squeaking. The friction factor was found to be highest in the largest clearance bearings under all test conditions. The incidence of squeaking was also highest in the large clearance bearings, with all bearings in this group squeaking throughout the study. A very low incidence of squeaking was observed in the other two clearance groups. The measured lubricating film was found to be lowest in the large clearance bearings. This study suggests that increasing the bearing clearance results in reduced lubricant film thickness, increased friction and an increased incidence of squeaking

An in vitro simulation model to assess the severity of edge loading and wear, due to variations in component positioning in hip joint replacements

The aim of this study was to develop a preclinical in vitro method to predict the occurrence and severity of edge loading condition associated with the dynamic separation of the centres of the head and cup (in the absence of impingement) for variations in surgical positioning of the cup. Specifically, this study investigated the effect of both the variations in the medial–lateral translational mismatch between the centres of the femoral head and acetabular cup and the variations in the cup inclination angles on the occurrence and magnitude of the dynamic separation, the severity of edge loading, and the wear rate of ceramic‐on‐ceramic hip replacement bearings in a multi‐station hip joint simulator during a walking gait cycle. An increased mismatch between the centres of rotation of the femoral head and acetabular cup resulted in an increased level of dynamic separation and an increase in the severity of edge loading condition which led to increased wear rate in ceramic‐on‐ceramic bearings. Additionally for a given translational mismatch, an increase in the cup inclination angle gave rise to increased dynamic separation, worst edge loading conditions, and increased wear. To reduce the occurrence and severity of edge loading, the relative positions (the mismatch) of the centres of rotation of the head and the cup should be considered alongside the rotational position of the acetabular cup. This study has considered the combination of mechanical and tribological factors for the first time in the medial–lateral axis only, involving one rotational angle (inclination) and one translational mismatch

Detailed Inspection of Metal Implants

Detailed visual inspection of metal hips is the first step in retrieval analysis. In this study a systematic visual inspection protocol was developed to quantify bearing surface changes and their associations with material loss was investigated. Simple and multiple linear regression models found that moderate surface scratching, discolouration, haziness and the size of visible wear scars were all significantly associated with material loss (R2 = 5% - 73%, p<0.05). Visual inspection is not a substitute for measurement of material loss but an understanding of bearing surface changes may offer unique clues as to the mechanisms of failure of retrieved hips

Chinese journals: a guide for epidemiologists.

Chinese journals in epidemiology, preventive medicine and public health contain much that is of potential international interest. However, few non-Chinese speakers are acquainted with this literature. This article therefore provides an overview of the contemporary scene in Chinese biomedical journal publication, Chinese bibliographic databases and Chinese journals in epidemiology, preventive medicine and public health. The challenge of switching to English as the medium of publication, the development of publishing bibliometric data from Chinese databases, the prospect of an Open Access publication model in China, the issue of language bias in literature reviews and the quality of Chinese journals are discussed. Epidemiologists are encouraged to search the Chinese bibliographic databases for Chinese journal articles.Published versio

A comparison of friction in 28 mm conventional and 55 mm resurfacing metal-on-metal hip replacements

Total hip replacement has been a common, successful surgical intervention for many years. However, it has long been considered unsatisfactory for younger, more active patients due to the limited survivorship of conventional implants employing polyethylene. Larger resurfacing implants were developed to preserve bone stock and improve stability, however, early metal-on-polyethylene implants failed due to high wear. More recent developments, utilizing a metal-on-metal bearing, have encouraging short- to medium-term clinical performance. Concerns exist regarding the increased sliding distance and frictional torque generated within a larger diameter bearing. A large diameter metal-on-metal surface replacement was contrasted with a conventional 28 mm diameter implant with the same bearing material combination using a pendulum friction simulator. Studies were performed under different swing-phase load and lubrication conditions. The larger diameter bearing exhibited the lower friction factor under all test conditions, although the measured frictional torque was higher. Increasing swing-phase load was shown to cause an increase in friction factor in all tests. Increased serum concentration resulted in a reduction in friction factor for both bearings. Variation of the friction factor with the head diameter suggested that fluid-film lubrication contributed to the reduction of friction

The Elite-Plus stem migrates more than the flanged Charnley stem: A clinical, radiographic, and radiostereometric analysis of 114 patients with an average of 7 years follow-up

Background and purpose The Charnley Elite-Plus stem was introduced in 1993 as a presumed improvement of the flanged Charnley stem. We started this study in 1996 to investigate the migratory pattern of the Elite-Plus stem. Patients and methods We followed 114 patients with osteoarthritis and a primary total hip replacement with the Elite-Plus stem. Mean age at the time of operation was 64 (50-76) years. The mean follow-up time was 6.5 (2-7) years. Radiographs were evaluated with respect to cementing technique, migration, and wear measured by radiostereometry (RSA). Results The stem survival was 98% (CI: 96-100) at 7 years and 92% (CI: 86-97) at 10 years. Mean migration of the femoral head was 0.35 mm (SD 0.3) medially, 0.51 mm (SD 0.6) distally, and 1.1 mm (SD 1.8) in the dorsal direction. Mean total point motion was 1.7 mm (SD 1.7). The migration of the stems stabilized after 5 years in the medial and dorsal directions, but continued to subside slightly. Migration along any of the axes was higher if the cementing technique was inferior. Interpretation Patients with a Charnley Elite-Plus stem and defects in the cement mantle or other signs of inferior implantation technique should be carefully monitored

High Annual Risk of Tuberculosis Infection among Nursing Students in South India: A Cohort Study

Background: Nurses in developing countries are frequently exposed to infectious tuberculosis (TB) patients, and have a high prevalence of TB infection. To estimate the incidence of new TB infection, we recruited a cohort of young nursing trainees at the Christian Medical College in Southern India. Annual tuberculin skin testing (TST) was conducted to assess the annual risk of TB infection (ARTI) in this cohort. Methodology/Principal Findings: 436 nursing students completed baseline two-step TST testing in 2007 and 217 were TST-negative and therefore eligible for repeat testing in 2008. 181 subjects completed a detailed questionnaire on exposure to tuberculosis from workplace and social contacts. A physician verified the questionnaire and clinical log book and screened the subjects for symptoms of active TB. The majority of nursing students (96.7%) were females, almost 84% were under 22 years of age, and 80% had BCG scars. Among those students who underwent repeat testing in 2008, 14 had TST conversions using the ATS/CDC/IDSA conversion definition of 10 mm or greater increase over baseline. The ARTI was therefore estimated as 7.8% (95%CI: 4.3-12.8%). This was significantly higher than the national average ARTI of 1.5%. Sputum collection and caring for pulmonary TB patients were both high risk activities that were associated with TST conversions in this young nursing cohort. Conclusions: Our study showed a high ARTI among young nursing trainees, substantially higher than that seen in the general Indian population. Indian healthcare providers and the Indian Revised National TB Control Programme will need to implement internationally recommended TB infection control interventions to protect its health care workforce

Validation of a 3D CT method for measurement of linear wear of acetabular cups: A hip simulator study

Background We evaluated the accuracy and repeatability of a 3D method for polyethylene acetabular cup wear measurements using computed tomography (CT). We propose that the method be used for clinical in vivo assessment of wear in acetabular cups. Material and methods Ultra-high molecular weight polyethylene cups with a titanium mesh molded on the outside were subjected to wear using a hip simulator. Before and after wear, they were (1) imaged with a CT scanner using a phantom model device, (2) measured using a coordinate measurement machine (CMM), and (3) weighed. CMM was used as the reference method for measurement of femoral head penetration into the cup and for comparison with CT, and gravimetric measurements were used as a reference for both CT and CMM. Femoral head penetration and wear vector angle were studied. The head diameters were also measured with both CMM and CT. The repeatability of the method proposed was evaluated with two repeated measurements using different positions of the phantom in the CT scanner. Results The accuracy of the 3D CT method for evaluation of linear wear was 0.51 mm and the repeatability was 0.39 mm. Repeatability for wear vector angle was 17?. Interpretation This study of metal-meshed hip-simulated acetabular cups shows that CT has the capacity for reliable measurement of linear wear of acetabular cups at a clinically relevant level of accuracy

Using PCR-Based Detection and Genotyping to Trace Streptococcus salivarius Meningitis Outbreak Strain to Oral Flora of Radiology Physician Assistant

We recently investigated three cases of bacterial meningitis that were reported from a midwestern radiology clinic where facemasks were not worn during spinal injection of contrast agent during myelography procedures. Using pulsed field gel electrophoresis we linked a case strain of S. salivarius to an oral specimen of a radiology physician assistant (RPA). We also used a real-time PCR assay to detect S. salivarius DNA within a culture-negative cerebrospinal fluid (CSF) specimen. Here we extend this investigation through using a nested PCR/sequencing strategy to link the culture-negative CSF specimen to the case strain. We also provide validation of the real-time PCR assay used, demonstrating that it is not solely specific for Streptococcus salivarius, but is also highly sensitive for detection of the closely related oral species Streptococcus vestibularis. Through using multilocus sequence typing and 16S rDNA sequencing we further strengthen the link between the CSF case isolate and the RPA carriage isolate. We also demonstrate that the newly characterized strains from this study are distinct from previously characterized S. salivarius strains associated with carriage and meningitis