Dynamic Modeling, Parameter Estimation and Control of a Leg Prosthesis Test Robot

Robotic testing can facilitate the development of new concepts, designs and control systems for prosthetic limbs. Human subject test clearances, safety and the lack of repeatability associated with human trials can be reduced or eliminated with automated testing, and test modalities are possible which are dangerous or inconvenient to attempt with patients. This paper describes the development, modeling, parameter estimation and control of a robot capable of reproducing two degree-of-freedom hip motion in the sagittal plane. Hip vertical displacement and thigh angle motion profiles are applied to a transfemoral prosthesis attached to the robot. A treadmill is used as walking surface. Aside from tracking hip motion trajectories, the control system can be used to regulate the contact force between the treadmill and the prosthesis. The paper summarizes the overall development process, with emphasis on the generation of a dynamic model that can be used to design closed-loop motion and force control algorithms

Vibration Modal Characterization of a Stirling Convertor via Base-Shake Excitation

The U.S. Department of Energy (DOE), Lockheed Martin (LM), Stirling Technology Company (STC), and NASA John H. Glenn Research Center (GRC) are currently developing a high-efficiency Stirling convertor for use in a Stirling Radioisotope Generator (SRG). NASA and DOE have identified the SRG for potential use as an advanced power system for future NASA Space Science missions, providing spacecraft onboard electric power for deep space missions and power for unmanned Mars rovers. Low-level, baseshake sine vibration tests were conducted on the Stirling Technology Demonstration Convertor (TDC), at NASA GRC's Structural Dynamics Laboratory, in February 2001, as part of the development of this Stirling technology. The purpose of these tests was to provide a better understanding of the TDC's internal dynamic response to external vibratory base excitations. The knowledge obtained can therein be used to help explain the success that the TDC enjoyed in its previous random vibration qualification tests (December 1999). This explanation focuses on the TDC s internal dynamic characteristics in the 50 to 250 Hz frequency range, which corresponds to the maximum input levels of its qualification random vibration test specification. The internal dynamic structural characteristics of the TDC have now been measured in two separate tests under different motoring and dynamic loading conditions: (1) with the convertor being electrically motored, under a vibratory base-shake excitation load, and (2) with the convertor turned off, and its alternator internals undergoing dynamic excitation via hammer impact loading. This paper addresses the test setup, procedure and results of the base-shake vibration testing conducted on the motored TDC, and will compare these results with those results obtained from the dynamic impact tests (May 2001) on the nonmotored TDC

Modeling and Optimal Control of an Energy-Storing Prosthetic Knee

Advanced prosthetic knees for transfemoral amputees are currently based on controlled damper mechanisms. Such devices require little energy to operate, but can only produce negative or zero joint power, while normal knee joint function requires alternative phases of positive and negative work. The inability to generate positive work may limit the user\u27s functional capabilities, may cause undesirable adaptive behavior, and may contribute to excessive metabolic energy cost for locomotion. In order to overcome these problems, we present a novel concept for an energy-storing prosthetic knee, consisting of a rotary hydraulic actuator, two valves, and a spring-loaded hydraulic accumulator. In this paper, performance of the proposed device will be assessed by computational modeling and by simulation of functional activities. A computational model of the hydraulic system was developed, with methods to obtain optimal valve control patterns for any given activity. The objective function for optimal control was based on tracking of joint angles, tracking of joint moments, and the energy cost of operating the valves. Optimal control solutions were obtained, based on data collected from three subjects during walking, running, and a sit-stand-sit cycle. Optimal control simulations showed that the proposed device allows near-normal knee function during all three activities, provided that the accumulator stiffness was tuned to each activity. When the energy storage mechanism was turned off in the simulations, the system functioned as a controlled damper device and optimal control results were similar to literature data on human performance with such devices. When the accumulator stiffness was tuned to walking, simulated performance for the other activities was sub-optimal but still better than with a controlled damper. We conclude that the energy-storing knee concept is valid for the three activities studied, that modeling and optimal control can assist the design process, and that further studies using human subjects are justified

Modeling and Optimal Control of an Energy-Storing Prosthetic Knee

Advanced prosthetic knees for transfemoral amputees are currently based on controlled damper mechanisms. Such devices require little energy to operate, but can only produce negative or zero joint power, while normal knee joint function requires alternative phases of positive and negative work. The inability to generate positive work may limit the user\u27s functional capabilities, may cause undesirable adaptive behavior, and may contribute to excessive metabolic energy cost for locomotion. In order to overcome these problems, we present a novel concept for an energy-storing prosthetic knee, consisting of a rotary hydraulic actuator, two valves, and a spring-loaded hydraulic accumulator. In this paper, performance of the proposed device will be assessed by computational modeling and by simulation of functional activities. A computational model of the hydraulic system was developed, with methods to obtain optimal valve control patterns for any given activity. The objective function for optimal control was based on tracking of joint angles, tracking of joint moments, and the energy cost of operating the valves. Optimal control solutions were obtained, based on data collected from three subjects during walking, running, and a sit-stand-sit cycle. Optimal control simulations showed that the proposed device allows near-normal knee function during all three activities, provided that the accumulator stiffness was tuned to each activity. When the energy storage mechanism was turned off in the simulations, the system functioned as a controlled damper device and optimal control results were similar to literature data on human performance with such devices. When the accumulator stiffness was tuned to walking, simulated performance for the other activities was sub-optimal but still better than with a controlled damper. We conclude that the energy-storing knee concept is valid for the three activities studied, that modeling and optimal control can assist the design process, and that further studies using human subjects are justified

A 3D printable device allowing fast and reproducible longitudinal preparation of mouse intestines

AbstractAccurate and reproducible analysis of mouse small and large intestinal lumen is key for research involving intestinal pathology in preclinical models. Currently, there is no easily accessible, standardized method that allows researchers of different skill levels to consistently dissect intestines in a time-efficient manner. Here, we describe the design and use of the 3D printed “Mouse Intestinal Slicing Tool” (MIST), which can be used to longitudinally prepare murine intestines for further analysis. We benchmarked the MIST against a commonly used procedure involving scissors to make a longitudinal cut along the intestines. Use of the MIST halved the time per mouse to prepare the intestines and outperformed alternative methods in smoothness of the cutting edge and general reproducibility. By sharing the plans for printing the MIST, we hope to contribute a uniformly applicable method for saving time and increasing consistency in studies of the mouse gastrointestinal tract.</jats:p