Properties of the Optical Planar Polymer Waveguides Deposited on Printed Circuit Boards

This paper reports on a technology for realization of an optical planar waveguide layer on duroid substrate and on FR4 fiber reinforced board material printed circuit boards. Waveguide core material was EpoCore polymer and for claddings we used EpoClad polymer. Design of the presented planar waveguides was realized on the bases of modified dispersion equation and was schemed for 633 nm, 964 nm, 1310 nm and 1550 nm wavelength. Waveguiding properties were measured by dark mode spectroscopy while propagation optical loss measurement was done by the fiber probe technique at wavelegnth 633 nm (He-Ne laser). The samples had optical losses lower than 0.5 dB/cm. The best sample has optical losses around 0.25 dB/cm

Design of the Novel Wavelength Triplexer Using Multiple Polymer Microring Resonators

We report about new design of wavelength triplexer using multiple polymer optical microring resonators. Triplexer consists of two downstream wavelength channels operating at 1490 ± 10 nm, 1555 ± 10 nm and one upstream wavelength channel operating at 1310 ± 50 nm. The parallel coupled double ring resonator was used for separation of the optical signal band at 1555 nm and filtered out signal bands 1310 nm and 1490 nm. The serially coupled triple optical microring resonator was used for separation of the optical signal band at 1490 nm and filtered out signal bands 1310 nm and 1555 nm. The design was done by using FullWAVETM software by the finite-difference time-domain method. Simulation showed that optical losses for band at 1555 nm were -3 dB and crosstalk between signal bands 1555 nm and 1490 nm was 24 dB. Calculated optical losses for channel 1490 nm were less than -2.5 dB and signal bands at 1555 nm was filtered out with less than 18 dB loss. The bands at 1310 nm were fully filtered out from both downstream wavelength channels operating at bands 1490 nm and 1555 nm

Flexible Polymer Planar Optical Waveguides

We report about design, fabrication and properties of flexible polymer optical planar waveguides made of Epoxy Novolak Resin as planar waveguides deposited on various foil substrates. The design of the presented planar waveguides was realized on the bases of modified dispersion equation and was schemed for 633 nm, 850 nm, 1310 nm and 1550 nm wavelength. Propagation optical loss measurements were done by the fibre probe technique at wavelegnth 633 nm (He-Ne laser) and samples have optical losses lower than 2 dB/cm. Unlike the up-to-now presented structures our constructin is fully flexible what makes it possible to be used in innovative photonics structures

Optical Splitters Based on Self-Imaging Effect in Multi-Mode Waveguide Made by Ion Exchange in Glass

Design and modeling of single mode optical multi-mode interference structures with graded refractive index is reported. Several samples of planar optical channel waveguides were obtained by Ag+Na+ and K+Na+ one step thermal ion exchange process in molten salt on GIL49 glass substrate and new special optical glass for ion exchange technology. Waveguide properties were measured by optical mode spectroscopy. Obtained data were used for further design and modeling of single mode channel waveguide and subsequently for the design of 1 to 3 multimode interference power splitter in order to improve simulation accuracy. Designs were developed by utilizing finite difference beam propagation method

Theoretical Model of the Bistable Semiconductor Laser Diode Based on the Rate Equations

The paper describes theoretical and experimental results that enabled the authors to proof optical bistability behavior of a specially modified bistable semiconductor laser diode (BLD) created on a structure with a saturable absorption section. A mathematical model of the light-current characteristic, condition for bistability and the basic parameters of the hysteresis loop were derived by solving a system of three rate equations. That system was used for simulation of the light-current characteristic and conditions of bistability of the realized BLDs. For selected operating points of the simulated light-current characteristic the parameters of hysteresis loop and element values of the BLD electrical equivalent circuit for small signal variations were calculated. The bistability was experimentally measured by the new time method devised for impulse bistability verification (IBV). The basic measured and calculated parameters of the hysteresis loop of the BLD light-current characteristic were compared

Design and Modeling of Symmetric Three Branch Polymer Planar Optical Power Dividers

Two types of polymer-based three-branch symmetric planar optical power dividers (splitters) were designed, multimode interference (MMI) splitter and triangular shape-spacing splitter. By means of modeling the real structures were simulated as made of Epoxy Novolak Resin on silicon substrate, with silica buffer layer and polymethylmethacrylate as protection cover layer. The design of polymer waveguide structure was done by Beam Propagation Method. After comparing properties of both types of the splitters we have demonstrated that our new polymer based triangular shaped splitter can work simultaneously in broader spectrum, the only condition would be that the waveguides are single-mode guiding. It practically means that, what concerns communication wavelengths, it can on principle simultaneously operate at two mainly used wavelengths, 1310 and 1550 nm

Study of Adjustable Gains for Control of Oscillation Frequency and Oscillation Condition in 3R-2C Oscillator

An idea of adjustable gain in order to obtain controllable features is very useful for design of tuneable oscillators. Several active elements with adjustable properties (current and voltage gain) are discussed in this paper. Three modified oscillator conceptions that are quite simple, directly electronically adjustable, providing independent control of oscillation condition and frequency were designed. Positive and negative aspects of presented method of control are discussed. Expected assumptions of adjustability are verified experimentally on one of the presented solution

Current Gain Controlled CCTA and its Application in Quadrature Oscillator and Direct Frequency Modulator

A modified conception of adjustable current conveyor transconductance amplifier (CCTA) and its interesting application in simple quadrature oscillator expandable for direct frequency modulation purposes, employing only four grounded passive elements is presented in this paper. It is quite simple solution for modern communication subsystem components. An electronic adjusting of the oscillation frequency is easily possible and control of condition of the oscillation is realized via only one grounded resistor. The characteristic equation, condition of oscillation and major parasitic influences of real active part are discussed. The verification includes PSpice simulation and measurement with the CCTA block formed by commercially available active elements