Controlled fabrication of single electron transistors from single-walled carbon nanotubes

Single electron transistors (SETs) are fabricated by placing single walled carbon nanotubes (SWNTs) on a 100 nm wide local Al/Al2O3 bottom gate and then contacting with Pd electrodes. Coulomb oscillations up to 125 K were observed and charging energies of 12-15 meV with level spacing of ~5 meV were measured from the Couloumb diamond, in agreement with a dot size of ~100 nm, implying that the local gate defines the dot size by bending SWNT at the edges and controls its operation. This "mechanical template" approach may facilitate large scale fabrication of SET devices using SWNT.Comment: 5 pages, 3 figure

Efros-Shklovskii variable range hopping in reduced graphene oxide sheets of varying carbon sp2 fraction

We investigate the low temperature electron transport properties of chemically reduced graphene oxide (RGO) sheets with different carbon sp2 fractions of 55 to 80 %. We show that in the low bias (Ohmic) regime, the temperature (T) dependent resistance (R) of all the devices follow Efros-Shklovskii variable range hopping (ES-VRH) R ~ exp[(T(ES)/T)^1/2] with T(ES) decreasing from 30976 to 4225 K and electron localization length increasing from 0.46 to 3.21 nm with increasing sp2 fraction. From our data, we predict that for the temperature range used in our study, Mott-VRH may not be observed even at 100 % sp2 fraction samples due to residual topological defects and structural disorders. From the localization length, we calculate a bandgap variation of our RGO from 1.43 to 0.21 eV with increasing sp2 fraction from 55 to 80 % which agrees remarkably well with theoretical prediction. We also show that, in the high bias regime, the hopping is field driven and the data follow R ~ exp[(E(0)/E)^1/2] providing further evidence of ES-VRH.Comment: 13 pages, 6 figures, 1 tabl

The Effect of Carbon Nanotube/Organic Semiconductor Interfacial Area on the Performance of Organic Transistors

We show that the performance of pentacene transistors can be significantly improved by maximizing the interfacial area at single walled carbon nanotube (SWCNT)/pentacene. The interfacial areas are varied by anchoring short SWCNTs of different densities (0-30/{\mu}m) to the Pd electrodes. The average mobility is increased three, six and nine times for low, medium and high SWCNT densities, respectively, compared to the devices with zero SWCNT. The current on-off ratio and on-current are increased up to 40 times and 20 times with increasing the SWCNT density. We explain the improved device performance using reduced barrier height of SWCNT/pentacene interface.Comment: 9 pages, 7 figures, 1 tabl

Fabrication of nanometer-spaced electrodes using gold nanoparticles

A simple and highly reproducible technique is demonstrated for the fabrication of metallic electrodes with nanometer separation. Commercially available bare gold colloidal nanoparticles are first trapped between prefabricated large-separation electrodes to form a low-resistance bridge by an ac electric field. A large dc voltage is then applied to break the bridge via electromigration at room temperature, which consistently produces gaps in the sub-10 nm range. The technique is readily applied to prefabricated electrodes with separation up to 1 micron, which can be defined using optical lithography. The simple fabrication scheme will facilitate electronic transport studies of individual nanostructures made by chemical synthesis. As an example, measurement of a thiol-coated gold nanoparticle showing a clear Coulomb staircase is presented.Comment: To appear in Appl. Phys. Lett. in Dec. 200

Space charge limited conduction with exponential trap distribution in reduced graphene oxide sheets

We elucidate on the low mobility and charge traps of the chemically reduced graphene oxide (RGO) sheets by measuring and analyzing temperature dependent current-voltage characteristics. The RGO sheets were assembled between source and drain electrodes via dielectrophoresis. At low bias voltage the conduction is Ohmic while at high bias voltage and low temperatures the conduction becomes space charge limited with an exponential distribution of traps. We estimate an average trap density of 1.75x10^16 cm^-3. Quantitative information about charge traps will help develop optimization strategies of passivating defects in order to fabricate high quality solution processed graphene devices.Comment: 6 pages, 3 figures, 1 tabl

Service Limit Criteria for Deflection and Cracking in Partially Prestressed Beams

This thesis has been concerned with the primary objective of studying the serviceability behavior of partially prestressed concrete beams. Seven simply supported rectangular beams were tested on an effective span of 2.745 m subjected to two third point loadings. The variables were the amount of prestressing wires and ordinary reinforcement steel. The effect of bond was also investigated. Four beams were fully bonded by using pressurised grouting while three other beams were tested unbonded. Crack widths and deflections were recorded at various loadings, and crack propagations observed. The results obtained were compared with theoretical values proposed by various authors. Results were also compared with the service limit criteria for cracking and deflection according to the British Standards code of practice, CP 110:1972. It was observed that the service limit criteria for cracking and deflection as set out by the code are too conservative for rectangular beams tested. It was found that the existing theory greatly underestimates the ultimate as well as service load carrying capacity and overestimates crack widths of partially prestressed concrete beams. It was also found that the nature of bonding has a great influence on crack widths and deflections. Bonded beams greatly improve on serviceability by having increased load carrying capacity and reduced crack width

Photoluminescence quenching in gold - MoS2 hybrid nanoflakes

Achieving tunability of two dimensional (2D) transition metal dichalcogenides (TMDs) functions calls for the introduction of hybrid 2D materials by means of localized interactions with zero dimensional (0D) materials. A metal-semiconductor interface, as in gold (Au) - molybdenum disulfide (MoS2), is of great interest from the standpoint of fundamental science as it constitutes an outstanding platform to investigate plasmonic-exciton interactions and charge transfer. The applied aspects of such systems introduce new options for electronics, photovoltaics, detectors, gas sensing, catalysis, and biosensing. Here we consider pristine MoS2 and study its interaction with Au nanoislands, resulting in local variations of photoluminescence (PL) associated with various Au-MoS2 hybrid configurations. By controllably depositing monolayers of Au on MoS2 to form Au nanostructures of given size and thickness, we investigate the electronic structure of the resulting hybrid systems. We present strong evidence of PL quenching of MoS2 as a result of charge transfer from MoS2 to Au: p-doping of MoS2. The results suggest new avenues for 2D nanoelectronics, active control of transport or catalytic properties