Effect of Surface Sealants and Polishing Time on Composite Surface Roughness and Microhardness

SUMMARY The objective of this study was to evaluate the effect of surface sealants and polishing delay time on a nanohybrid resin composite roughness and microhardness. Eighty disc specimens were made with a nanohybrid resin (Esthet-X HD, Dentsply). The specimens were divided into two groups (n=40) according to polishing time: immediate, after 10 minutes; delayed, after 48 hours. Each group was subdivided into four groups (n=10), according to the surface treatment: CG, control–rubber points (Jiffy Polishers, Ultradent); PP, rubber points + surface sealant (PermaSeal, Ultradent); PF, rubber points + surface sealant (Fortify, Bisco); PB, rubber points + surface sealant (BisCover, Bisco). Surface roughness (Ra) and microhardness (50 g/15 seconds) were measured. Surface morphology was analyzed by scanning electron microscopy and atomic force microscopy. The data were analyzed statistically using one-way analysis of variance and the Games-Howell post hoc test (α=0.05). PermaSeal roughness (G2) in the delayed polishing group was significantly higher (p=0.00) than that of the other groups. No difference was observed among the groups between immediate and delayed polishing (p=1.00), except for PermaSeal (p=0.00). Moreover, PermaSeal showed the lowest microhardness values (p=0.00) for immediate polishing. Microhardness was higher at delayed polishing for all the surface treatments (p=0.00) except Fortify (p=0.73). Surface smoothness similar to polishing with rubber points was achieved when surface sealants were used, except for PermaSeal surface sealant, which resulted in a less smooth resin composite surface. However, surface sealant application did not significantly improve composite resin microhardness.</jats:p

Tooth Fragment Reattachment: A Case Report

SUMMARY The aim of this article is to present a case report for the multidisciplinary treatment of anterior tooth fractures with invasion of the biologic width and pulpectomy. Successful esthetic and functional results were achieved by bonding the crown fragment, without any form of preparation or the utilization of intracanal posts.</jats:p

A Conservative Technique for Repairing Class IV Composite Restorations

SUMMARY Composite resin may make a restoration noticeable as time passes, on account of its color instability. The repair technique is a minimally invasive treatment for class IV composite resin restorations that show unsatisfactory coloration. Thus, the objective of the present article was to report a clinical case involving a conservative technique used for repairing a class IV composite resin restoration in the left maxillary central incisor and the replacement of a class IV restoration in the right maxillary central incisor.</jats:p

Ceramic Veneers and Direct-Composite Cases of Amelogenesis Imperfecta Rehabilitation

SUMMARY The aim of this article is to present two case reports for the treatment of patients affected with amelogenesis imperfecta. One case was treated with composite resin and the other case with ceramic veneers. Esthetic and functional results were achieved using both treatments, and a review of advantages and disadvantages is presented.</jats:p

Cracked Tooth Syndrome in an Unrestored Maxillary Premolar: A Case Report

SUMMARY Cracked tooth syndrome is known to occur most frequently in heavily restored teeth. Nevertheless, when the symptoms occur in intact teeth, there is difficulty in obtaining a correct diagnosis because it is difficult for the dentist to find where the crack is located. This clinical report describes the diagnostic procedures and the direct bonded composite restoration used to restore an incompletely fractured unrestored maxillary premolar in a 22-year-old female patient. To achieve a correct diagnosis, the following were performed: periapical and bitewing radiographs, percussion and thermal vitality tests, a bite test, and the placement of a stainless steel band. Once the symptoms ceased with band placement, cone beam computed tomography, transillumination, macro photographs, and isolation with a rubber dam helped to visualize the crack line along the occlusal surface involving distal and mesial marginal ridges. The crack was traced using a high-speed tungsten carbide bur until the fracture line was not visible. The tooth was restored with a direct composite resin, associated with a total-etch adhesive system, and the symptoms were immediately eliminated.</jats:p

Reattachment of subgingivally fractured central incisor with an open apex

WOS: 000247138900013PubMed ID: 17511842A case report of a 6-year-old girl with a fractured maxillary left central incisor with an open apex is presented. The procedure used to repair the fracture included flap surgery with an intrasulcular incision and endodontic treatment. The patient was called for 3 months regular follow-up to check the root formation. At the end of 32 months just before the root was obturated by guttaperka, she fractured the same tooth. Flap surgery was repeated and the tooth was restored. The root canal was obturated with a root filling paste and guttaperka as the apex was closed. Examination 10 months after treatment revealed good periodontal health, aesthetics and normal function