The influence of thermal storage on microgeneration flexibility

In a future power system, the ability to manipulate generation and load will be a critical factor in providing a secure and stable supply of electrical energy to consumers. Using a simulation-based approach, this study assesses the ability of thermal storage to help deliver flexibility in the operation of domestic micro-generation technologies without sacrificing householder comfort and convenience. A typical UK detached dwelling is modelled along with its heating system, which features a retro-fitted air source heat pump (ASHP). The model is used to determine the maximum possible temporal shift for different capacities and configurations of thermal storage, taking into account the influence of climate, building fabric, control settings and occupancy. The limits of time shifting are dictated by the living space temperature and the hot water temperature delivered to the occupants. The storage mechanisms examined are: the basic thermal inertia of the building fabric; increasing the space heating set point temperatures to increase fabric storage and inserting a dedicated thermal buffer between the ASHP and the heat distribution system. The simulation results indicate that back-shifting of the ASHP start/stop times of between one and two hours are possible without causing serious discomfort or inconvenience to the occupants

Comparison of nonlinear dynamic inversion and inverse simulation

No abstract available

Sensitivity-analysis method for inverse simulation application

An important criticism of traditional methods of inverse simulation that are based on the Newton–Raphson algorithm is that they suffer from numerical problems. In this paper these problems are discussed and a new method based on sensitivity-analysis theory is developed and evaluated. The Jacobian matrix may be calculated by solving a sensitivity equation and this has advantages over the approximation methods that are usually applied when the derivatives of output variables with respect to inputs cannot be found analytically. The methodology also overcomes problems of input-output redundancy that arise in the traditional approaches to inverse simulation. The sensitivity- analysis approach makes full use of information within the time interval over which key quantities are compared, such as the difference between calculated values and the given ideal maneuver after each integration step. Applications to nonlinear HS125 aircraft and Lynx helicopter models show that, for this sensitivity-analysis method, more stable and accurate results are obtained than from use of the traditional Newton–Raphson approach

Feedback methods for inverse simulation of dynamic models for engineering systems applications

Inverse simulation is a form of inverse modelling in which computer simulation methods are used to find the time histories of input variables that, for a given model, match a set of required output responses. Conventional inverse simulation methods for dynamic models are computationally intensive and can present difficulties for high-speed applications. This paper includes a review of established methods of inverse simulation,giving some emphasis to iterative techniques that were first developed for aeronautical applications. It goes on to discuss the application of a different approach which is based on feedback principles. This feedback method is suitable for a wide range of linear and nonlinear dynamic models and involves two distinct stages. The first stage involves design of a feedback loop around the given simulation model and, in the second stage, that closed-loop system is used for inversion of the model. Issues of robustness within closed-loop systems used in inverse simulation are not significant as there are no plant uncertainties or external disturbances. Thus the process is simpler than that required for the development of a control system of equivalent complexity. Engineering applications of this feedback approach to inverse simulation are described through case studies that put particular emphasis on nonlinear and multi-input multi-output models

A Comparison of Inverse Simulation-Based Fault Detection in a Simple Robotic Rover with a Traditional Model-Based Method

Robotic rovers which are designed to work in extra-terrestrial environments present a unique challenge in terms of the reliability and availability of systems throughout the mission. Should some fault occur, with the nearest human potentially millions of kilometres away, detection and identification of the fault must be performed solely by the robot and its subsystems. Faults in the system sensors are relatively straightforward to detect, through the residuals produced by comparison of the system output with that of a simple model. However, faults in the input, that is, the actuators of the system, are harder to detect. A step change in the input signal, caused potentially by the loss of an actuator, can propagate through the system, resulting in complex residuals in multiple outputs. These residuals can be difficult to isolate or distinguish from residuals caused by environmental disturbances. While a more complex fault detection method or additional sensors could be used to solve these issues, an alternative is presented here. Using inverse simulation (InvSim), the inputs and outputs of the mathematical model of the rover system are reversed. Thus, for a desired trajectory, the corresponding actuator inputs are obtained. A step fault near the input then manifests itself as a step change in the residual between the system inputs and the input trajectory obtained through inverse simulation. This approach avoids the need for additional hardware on a mass- and power-critical system such as the rover. The InvSim fault detection method is applied to a simple four-wheeled rover in simulation. Additive system faults and an external disturbance force and are applied to the vehicle in turn, such that the dynamic response and sensor output of the rover are impacted. Basic model-based fault detection is then employed to provide output residuals which may be analysed to provide information on the fault/disturbance. InvSim-based fault detection is then employed, similarly providing \textit{input} residuals which provide further information on the fault/disturbance. The input residuals are shown to provide clearer information on the location and magnitude of an input fault than the output residuals. Additionally, they can allow faults to be more clearly discriminated from environmental disturbances

'They're battle scars, I wear them well': A phenomenological exploration of young women's experiences of building resilience following adversity in adolescence

This is an Author's Accepted Manuscript of an article published in Journal of Youth Studies, 13(3), 273 - 290, 2010 [copyright Taylor & Francis], available online at: http://www.tandfonline.com/10.1080/13676260903520886.This phenomenological study explored young women's accounts of building resilience following chains of adverse life experiences in adolescence. Six participants were interviewed, aged 20–25 years. Most had, or were receiving, a university education. They described their recovery from adversity as starting with certain pivotal moments, followed by both short-term and longer-term strategies. Short-term strategies tended to offer respite from distress and emotional comfort, increased clarity about their experiences and social affirmation. Recovery involved gaining new perspectives on their adverse situation and recovering a positive self-image through three longer-term strategies. These involved making visible progress in their education, rebuilding relationships with family and friends, and participating in the ‘normalizing’ activities and developmental projects of adolescence. Participants believed that they were stronger and more compassionate although positive achievements co-existed with some regrets. Most perceived the adversity as catalyzing personal growth. These accounts of resilience revealed the complex psychosocial processes and resources available to some adolescents

Diagramming social practice theory:An interdisciplinary experiment exploring practices as networks

Achieving a transition to a low-carbon energy system is now widely recognised as a key challenge facing humanity. To date, the vast majority of research addressing this challenge has been conducted within the disciplines of science, engineering and economics utilising quantitative and modelling techniques. However, there is growing awareness that meeting energy challenges requires fundamentally socio-technical solutions and that the social sciences have an important role to play. This is an interdisciplinary challenge but, to date, there remain very few explorations of, or reflections on, interdisciplinary energy research in practice. This paper seeks to change that by reporting on an interdisciplinary experiment to build new models of energy demand on the basis of cutting-edge social science understandings. The process encouraged the social scientists to communicate their ideas more simply, whilst allowing engineers to think critically about the embedded assumptions in their models in relation to society and social change. To do this, the paper uses a particular set of theoretical approaches to energy use behaviour known collectively as social practice theory (SPT) - and explores the potential of more quantitative forms of network analysis to provide a formal framework by means of which to diagram and visualize practices. The aim of this is to gain insight into the relationships between the elements of a practice, so increasing the ultimate understanding of how practices operate. Graphs of practice networks are populated based on new empirical data drawn from a survey of different types (or variants) of laundry practice. The resulting practice networks are analysed to reveal characteristics of elements and variants of practice, such as which elements could be considered core to the practice, or how elements between variants overlap, or can be shared. This promises insights into energy intensity, flexibility and the rootedness of practices (i.e. how entrenched/ established they are) and so opens up new questions and possibilities for intervention. The novelty of this approach is that it allows practice data to be represented graphically using a quantitative format without being overly reductive. Its usefulness is that it is readily applied to large datasets, provides the capacity to interpret social practices in new ways, and serves to open up potential links with energy modeling. More broadly, a significant dimension of novelty has been the interdisciplinary approach, radically different to that normally seen in energy research. This paper is relevant to a broad audience of social scientists and engineers interested in integrating social practices with energy engineering

The Dynamics of Zeroth-Order Ultrasensitivity: A Critical Phenomenon in Cell Biology

It is well known since the pioneering work of Goldbeter and Koshland [Proc. Natl. Acad. Sci. USA, vol. 78, pp. 6840-6844 (1981)] that cellular phosphorylation- dephosphorylation cycle (PdPC), catalyzed by kinase and phosphatase under saturated condition with zeroth order enzyme kinetics, exhibits ultrasensitivity, sharp transition. We analyse the dynamics aspects of the zeroth order PdPC kinetics and show a critical slowdown akin to the phase transition in condensed matter physics. We demonstrate that an extremely simple, though somewhat mathematically "singular" model is a faithful representation of the ultrasentivity phenomenon. The simplified mathematical model will be valuable, as a component, in developing complex cellular signaling network theory as well as having a pedagogic value.Comment: 8 pages, 3 figure