Holographic laser Doppler imaging of pulsatile blood flow

We report on wide-field imaging of pulsatile motion induced by blood flow using heterodyne holographic interferometry on the thumb of a healthy volunteer, in real-time. Optical Doppler images were measured with green laser light by a frequency-shifted Mach-Zehnder interferometer in off-axis configuration. The recorded optical signal was linked to local instantaneous out-of-plane motion of the skin at velocities of a few hundreds of microns per second, and compared to blood pulse monitored by plethysmoraphy during an occlusion-reperfusion experiment.Comment: 5 pages, 5 figure

Passive Temperature-Compensating Technique for Microstructured Fiber Bragg Gratings

The thermal drift of the characteristic wavelength of fiber Bragg gratings (FBGs) photowritten in the core of microstructured fibers (MOFs) is significantly reduced by inserting a liquid of suitable refractive index into their holes. For instance, the spectral range of variations is divided by a factor of 4 over a temperature range larger than 20\degree C in a six-hole MOF, and the maximum sensitivity is reduced. Such passive FBG temperature compensation technique is of great interest for applications involving accurate sensing free of thermal effects

Numerical and experimental analysis of the birefringence of large air fraction slightly unsymmetrical holey fibres

International audienceCareful numerical computations show that very slight geometrical imperfections of the cross-section of actual large air-fraction holey fibres (d/Λ > 0.6) may induce surprisingly high birefringence, corresponding to beat lengths as short as few millimeters. The spectral variations of this birefringence obeys laws similar to those of elliptical core Hi-Bi holey fibres with low air-fraction. For all the tested fibres, the group birefringence numerically deduced from the only shape birefringence is in good agreement with the measured one that does not varies when strongly heating the fibres. These computations and measurements show that the contribution of possible inner stress to the birefringence is negligible

Influence of a single asperity on stresses during lubricated sliding contact on DLC-coated system

http://tribo-lyon2013.sciencesconf.org/18528International audienceExtreme low wear rates of Diamond-Like Carbon (DLC) coatings are one the properties that makes them particularly interesting for numerous applications, like automotive ones. This property is often observed during characterisation tests under basic sollicitations like fretting, sliding, rolling-sliding. However, tests on cam-tappet systems show the coating lifetime can be highly reduced under special coupled conditions, such as the presence of an asperity breaking through the lubrication film into the contact area. Its influence on surface and subsurface stresses has to be quanti ed to eventually obtain a predictive model of the coating lifetime. The purpose of this study is to develop a simpli ed numerical model that is consistent with elasto-hydrodynami-lubrication (EHD) approxima- tions for estimating the stress perturbation due to such an asperity

Experimental and numerical analysis of the chromatic dispersion dependence upon the actual profile of small core microstructured fibres

International audienceThe chromatic dispersion curve of the fundamental mode in small core microstructured fibres (SCMF) is both calculated using a Finite Element Method (FEM) and measured with a low coherence interferometric method. The great sensitivity of the chromatic dispersion to variations of the geometrical parameters of SCMFs (the pitch and the diameter) is pointed out. An excellent agreement is obtained between the numerical and the experimental results over a half micrometer spectral bandwidth [1.1 µm-1.6 µm]

REFROIDISSEMENT MOLECULAIRE INDUIT PAR CHAMP ELECTRIQUE ; MISE EN EVIDENCE PAR SPECTROSCOPIE NON LINEAIRE CARS

National audienceNous avons montré qu'un refroidissement moléculaire pouvait être induit par un champ électrique statique appliqué à des molécules non polaires d'huile de paraffine. Cet effet a été mis en évidence grâce à une mesure de spectroscopie CARS (Coherent Anti-Stokes Raman Scattering). De manière complémentaire, l'exposition de molécules à un champ électrique permet de contrôler leur orientation et ainsi améliorer ou diminuer l'amplitude de leur signature vibrationnelle

Role of stabilisers in the design of Ti aqueous suspensions for pressure slip casting

Colloidal processing has long been used in ceramics to achieve green bodies with high densities, complex shapes and homogeneous microstructures, but they are rarely used to shape metal powders because of their high density and high surface reactivity. However, the possibility of processing fine particles makes these techniques interesting for metals, such as titanium, with a low density and high melting point. This work presents encouraging results in the design of aqueous suspensions of Ti particles to be shaped into bulk pieces by pressure slip casting (PSC), which opens new paths for the processing of fine and complex microstructures. Ti powders, measuring 10 μm in size, and mixtures of Ti and Al₂O₃ powders (added up to 5 wt.%) were dispersed in water by the addition of different stabilisers. The influence of the stabilisers in the slurry behaviour (in terms of nature, stereochemistry and active functional groups) was determined, as well as the incorporation of ceramic particles. A polyacrylic-based dispersant was selected as the best stabiliser to incorporate a second component (Al₂O₃) into the Ti suspension, whereas shear-thinning additives, such as TIRON, are preferred for PSC shaping. Suspensions with 1 wt.% Al₂O₃ were selected for processing composites by PSC and sintering. Sintered materials were characterised by measuring the density, oxygen content, hardness and microstructure analysis by SEM. Ti bulk pieces with 97% density and fine and homogeneous microstructure, of which the relationship between the oxygen content and hardness agrees with that measured for CPTi grade 4 (249 ± 24 HV30), can be processed by PSC.The authors would like to acknowledge the financial support from the Spanish Government through the projects MAT 2009-14448-C02-01 and 02, MAT2012 38650-C02-01 and 02 and to the regional government of Madrid through the programme Estrumat (Ref. S2009/MAT-1585)