Analysis and documentation of QCSEE (Quiet Clean Short-haul Experimental Engine) over-the-wing exhaust system development

A static scale model test program was conducted in the static test area of the NASA-Langley 9.14- by 18.29 m(30- by 60-ft) Full-Scale Wind Tunnel Facility to develop an over-the-wing (OTW) nozzle and reverser configuration for the Quiet Clean Short-Haul Experimental Engine (QCSEE). Three nozzles and one basic reverser configuration were tested over the QCSEE takeoff and approach power nozzle pressure ratio range between 1.1 and 1.3. The models were scaled to 8.53% of QCSEE engine size and tested behind two 13.97-cm (5.5-in.) diameter tip-turbine-driven fan simulators coupled in tandem. An OTW nozzle and reverser configuration was identified which satisfies the QCSEE experimental engine requirements in terms of nozzle cycle area variation capability and reverse thrust level, and provides good jet flow spreading over a wing upper surface for achievement of high propulsive lift performance

ANALISIS FAKTOR-FAKTOR YANG MEMPENGARUHI CADANGAN DEVISA INDONESIA PERIODE 1999-2013

ABSTRAK Perekonomian Indonesia saat ini sudah tidak dapat terpisahkan lagi dengan perekonomian dunia. Hal ini terjadi setelah dianutnya sistem perekonomian terbuka yang dalam aktivitasnya selalu berhubungan dan tidak lepas dari fenomena hubungan internasional. Adanya keterbukaan perekonomian ini berdampak pada perkembangan neraca pembayaran suatu negara yang meliputi arus perdagangan dan lalu lintas modal luar negeri suatu negara. Salah satu bentuk aliran modal yang masuk ke dalam negeri yaitu dapat berupa devisa yang berasal dari perdagangan internasional yang dilakukan oleh negara tersebut. Meningkatnya ekspor suatu negara akan membawa keuntungan yaitu kenaikan pendapatan, kenaikan devisa, transfer modal dan makin banyaknya kesempatan kerja. Penelitian ini bertujuan untuk mengkaji sejauh mana variabel-variabel bebas seperti laju pertumbuhan ekonomi, kurs, utang luar negeri dan ekspor berpengaruh terhadap cadangan devisa Indonesia Tahun 1999-2013. Metode analisis yang digunakan adalah Ordinary Least Square (OLS) dengan metode analisis linear berganda diregresi menggunakan E-Views 6. Dalam penelitian ini, dibuktikan dengan uji-F, bahwa variabel laju pertumbuhan ekonomi Indonesia, nilai tukar/kurs, utang luar negeri, dan ekspor secara bersama-sama berpengaruh secara signifikan terhadap cadangan devisa Indonesia. Berdasarkan uji-t, secara parsial, variabel laju pertumbuhan ekonomi Indonesia memiliki hubungan negatif dan tidak signifikan, nilai tukar (kurs) memiliki hubungan negatif dan signifikan terhadap cadangan devisa Indonesia. Utang luar negeri dan ekspor berpengaruh positif dan signifikan terhadap cadangan devisa Indonesia. Kata Kunci : Cadangan Devisa Indonesia, Laju Pertumbuhan Ekonomi, Nilai Tukar (Kurs), Utang Luar Negeri, dan Ekspor

Thrust reverser design studies for an over-the-wing STOL transport

Aerodynamic and acoustics analytical studies were conducted to evaluate three thrust reverser designs for potential use on commercial over-the-wing STOL transports. The concepts were: (1) integral D nozzle/target reverser, (2) integral D nozzle/top arc cascade reverser, and (3) post exit target reverser integral with wing. Aerodynamic flowpaths and kinematic arrangements for each concept were established to provide a 50% thrust reversal capability. Analytical aircraft stopping distance/noise trade studies conducted concurrently with flow path design showed that these high efficiency reverser concepts are employed at substantially reduced power settings to meet noise goals of 100 PNdB on a 152.4 m sideline and still meet 609.6 m landing runway length requirements. From an overall installation standpoint, only the integral D nozzle/target reverser concept was found to penalize nacelle cruise performance; for this concept a larger nacelle diameter was required to match engine cycle effective area demand in reverse thrust

Constraints From b→sγb \to s\gamma on the Left-Right Symmetric Model

Recent results from the CLEO Collaboration on both inclusive and exclusive radiative $B$ decays are used to constrain the parameter space of two versions of the Left-Right Symmetric Model. In the first scenario, when the left- and right-handed Cabibbo-Kobayashi-Maskawa mixing matrices are equal, $V_L=V_R$, the radiative $B$ decay data is shown to lead to strong bounds on the $W_L-W_R$ mixing angle that are quite insensitive to either the top quark or $W_R$ mass. The second scenario examined is that of Gronau and Wakaizumi wherein $b$-quark decays proceed only via right-handed currents and $V_L$ and $V_R$ are quite distinct. For this model, the combined constraints from Tevatron $W_R$ searches, the $B$ lifetime, and radiative $B$ decays lead to a very highly restricted allowed range for the $W_L-W_R$ mixing angle.Comment: 16 pages, 9 figures(not included), LaTex, SLAC-PUB-642

Metal to ceramic joining for high temperature applications

The phenomenal growth rate for the use of engineering ceramics is attributed to successful scientific responses to industrial demand. These materials are replacing metal and its alloys in diverse applications from cutting tools and heat engine components to integrated circuits. Joining technology plays a vital role in this changing and evolving technology as success and failure comes with breaking new barriers. It is important to improve existing techniques and to develop new techniques that reliably join simple shape components to form complex assemblies or join dissimilar materials such as metal to ceramic. Joining of ceramics is not simple due to their high chemical stability and low coefficient of thermal expansion (CTE). Joining between metal and ceramic is usually carried out at elevated temperatures and upon cooling thermal residual stresses are induced that lead to joint failure or poor strength. Most metal-ceramic joints cannot be used over 500°C primarily due to the low melting temperature of the interlayer. This investigation was concerned with the successful joining for higher temperature applications (above 500°C) of two dissimilar high temperature oxidation and corrosion resistant materials, Fecralloy and silicon nitride. The primary focus was on the effects of process conditions upon the microstructure and mechanical properties of the joint and to also study/identify the joining mechanism. Two novel techniques were employed to join successfully the metal to ceramic. The first was by use of a thin Cu foil that did not remain after joining. Joining occurs by a process that results in partial melting of the Fecralloy interface, where Fe, Cr, Al and Cu reactively infiltrate into the silicon nitride. This liquid mixture causes partial dissolution of the silicon nitride interface, where Si and N diffuse into the Fecralloy. A thin reaction product layer was formed at the silicon nitride interface and our results suggested that this was AIN. The free surface Si and porosity of the silicon nitride along with the eutectic temperatures above 1100°C are all vital for this joining process. The highest average shear strength of a Fecralloy-silicon nitride joint produced by the method was 67.5 MPa. The second route was that of a powder metallurgy one, where cold pressed Ni-Al (1:1 molar) compacts were used to join successfully the Fecralloy to silicon nitride. The formation of NiAl from its constituents is highly exothermic and this is initiated between 500-650°C. The high temperature reached causes partial melting of the Fecralloy interface and dissolution/reactive wetting at the silicon nitride interface. Mostly Fe infiltrates the NiAl improving room temperature ductility, fracture toughness and yield strength. Molten Al from the interlayer reacts and wets the silicon nitride interface with small amount of infiltration and no reaction product forming. The reaction synthesis of NiAl was studied using DTA and TGA, where the effects of Ni particle size and heating rate were investigated. This joining process is highly dependant upon process conditions, the most important of which are applied pressure, heating rate and Ni/A1 particle size. The highest average shear strength attained was 94.30 MPa and this is attributed to good interfacial bonding, high pressure, moderate process temperature and dwell time. The exothermic formation of the NiAl interlayer that is densified and monophase was paramount for this joining process. The Bansal-Doremus kinetic model for evaluating the kinetic parameters from non-isothermal DTA data was shown to be valid. The results obtained were identical to those by other authors who used a different model and approach.EThOS - Electronic Theses Online ServiceGBUnited Kingdo

TRY plant trait database - enhanced coverage and open access

Plant traits-the morphological, anatomical, physiological, biochemical and phenological characteristics of plants-determine how plants respond to environmental factors, affect other trophic levels, and influence ecosystem properties and their benefits and detriments to people. Plant trait data thus represent the basis for a vast area of research spanning from evolutionary biology, community and functional ecology, to biodiversity conservation, ecosystem and landscape management, restoration, biogeography and earth system modelling. Since its foundation in 2007, the TRY database of plant traits has grown continuously. It now provides unprecedented data coverage under an open access data policy and is the main plant trait database used by the research community worldwide. Increasingly, the TRY database also supports new frontiers of trait-based plant research, including the identification of data gaps and the subsequent mobilization or measurement of new data. To support this development, in this article we evaluate the extent of the trait data compiled in TRY and analyse emerging patterns of data coverage and representativeness. Best species coverage is achieved for categorical traits-almost complete coverage for 'plant growth form'. However, most traits relevant for ecology and vegetation modelling are characterized by continuous intraspecific variation and trait-environmental relationships. These traits have to be measured on individual plants in their respective environment. Despite unprecedented data coverage, we observe a humbling lack of completeness and representativeness of these continuous traits in many aspects. We, therefore, conclude that reducing data gaps and biases in the TRY database remains a key challenge and requires a coordinated approach to data mobilization and trait measurements. This can only be achieved in collaboration with other initiatives

Growth and yield of mixed versus pure stands of Scots pine (Pinus sylvestris L. ) and European beech (Fagus sylvatica L.) analysed along a productivity gradient through Europe

Mixing of complementary tree species may increase stand productivity, mitigate the effects of drought and other risks, and pave the way to forest production systems which may be more resource-use efficient and stable in the face of climate change. However, systematic empirical studies on mixing effects are still missing for many commercially important and widespread species combinations. Here we studied the growth of Scots pine (Pinus sylvestris L.) and European beech (Fagus sylvatica L.) in mixed versus pure stands on 32 triplets located along a productivity gradient through Europe, reaching from Sweden to Bulgaria and from Spain to the Ukraine. Stand inventory and taking increment cores on the mainly 60-80 year-old trees and 0.02-1.55 ha sized, fully stocked plots provided insight how species mixing modifies the structure, dynamics and productivity compared with neighbouring pure stands. In mixture standing volume (+12 %), stand density (+20 %), basal area growth (+12 %), and stand volume growth (+8 %) were higher than the weighted mean of the neighbouring pure stands. Scots pine and European beech contributed rather equally to the overyielding and overdensity. In mixed stands mean diameter (+20 %) and height (+6 %) of Scots pine was ahead, while both diameter and height growth of European beech were behind (−8 %). The overyielding and overdensity were independent of the site index, the stand growth and yield, and climatic variables despite the wide variation in precipitation (520-1175 mm year−1), mean annual temperature (6-10.5 °C), and the drought index by de Martonne (28-61 mm °C−1) on the sites. Therefore, this species combination is potentially useful for increasing productivity across a wide range of site and climatic conditions. Given the significant overyielding of stand basal area growth but the absence of any relationship with site index and climatic variables, we hypothesize that the overyielding and overdensity results from several different types of interactions (light-, water-, and nutrient-related) that are all important in different circumstances. We discuss the relevance of the results for ecological theory and for the ongoing silvicultural transition from pure to mixed stands and their adaptation to climate change.The networking in this study has been sup-ported by COST Action FP1206 EuMIXFOR. All contributors thanktheir national funding institutions to establish, measure, and analysedata from the triplets. The first author also thanks the BayerischenStaatsforsten (BaySF) for supporting the establishment of the plots,the Bavarian State Ministry for Nutrition, Agriculture, and Forestryfor permanent support of the project W 07 ‘‘Long-term experimentalplots for forest growth and yield research’’ (# 7831-22209-2013) andthe German Science Foundation for providing the funds for the pro-jects PR 292/12-1 ‘‘Tree and stand-level growth reactions on droughtin mixed versus pure forests of Norway spruce and European beech’’.Thanks are also due to Ulrich Kern for the graphical artwork, and totwo anonymous reviewers for their constructive criticism

Management of cytoskeleton architecture by molecular chaperones and immunophilins

Cytoskeletal structure is continually remodeled to accommodate normal cell growth and to respond to pathophysiological cues. As a consequence, several cytoskeleton-interacting proteins become involved in a variety of cellular processes such as cell growth and division, cell movement, vesicle transportation, cellular organelle location and function, localization and distribution of membrane receptors, and cell-cell communication. Molecular chaperones and immunophilins are counted among the most important proteins that interact closely with the cytoskeleton network, in particular with microtubules and microtubule-associated factors. In several situations, heat-shock proteins and immunophilins work together as a functionally active heterocomplex, although both types of proteins also show independent actions. In circumstances where homeostasis is affected by environmental stresses or due to genetic alterations, chaperone proteins help to stabilize the system. Molecular chaperones facilitate the assembly, disassembly and/or folding/refolding of cytoskeletal proteins, so they prevent aberrant protein aggregation. Nonetheless, the roles of heat-shock proteins and immunophilins are not only limited to solve abnormal situations, but they also have an active participation during the normal differentiation process of the cell and are key factors for many structural and functional rearrangements during this course of action. Cytoskeleton modifications leading to altered localization of nuclear factors may result in loss- or gain-of-function of such factors, which affects the cell cycle and cell development. Therefore, cytoskeletal components are attractive therapeutic targets, particularly microtubules, to prevent pathological situations such as rapidly dividing tumor cells or to favor the process of cell differentiation in other cases. In this review we will address some classical and novel aspects of key regulatory functions of heat-shock proteins and immunophilins as housekeeping factors of the cytoskeletal network.Fil: Quintá, Héctor Ramiro. Consejo Nacional de Investigaciones Científicas y Técnicas. Instituto de Biología y Medicina Experimental (i); ArgentinaFil: Galigniana, Natalia Maricel. Consejo Nacional de Investigaciones Científicas y Técnicas. Instituto de Biología y Medicina Experimental (i); ArgentinaFil: Erlejman, Alejandra Giselle. Universidad de Buenos Aires. Facultad de Ciencias Exactas y Naturales. Departamento de Química Biológica; ArgentinaFil: Lagadari, Mariana. Consejo Nacional de Investigaciones Científicas y Técnicas. Instituto de Biología y Medicina Experimental (i); ArgentinaFil: Piwien Pilipuk, Graciela. Consejo Nacional de Investigaciones Científicas y Técnicas. Instituto de Biología y Medicina Experimental (i); ArgentinaFil: Galigniana, Mario Daniel. Consejo Nacional de Investigaciones Científicas y Técnicas. Instituto de Biología y Medicina Experimental (i); Argentina. Universidad de Buenos Aires. Facultad de Ciencias Exactas y Naturales. Departamento de Química Biológica; Argentin

Comparison of strontium isotope ratios in Mexican human hair and tap water as provenance indicators

Deceased undocumented border crossers are some of the most difficult individuals to identify due to the inability to narrow down the region of origin and therefore to obtain family reference samples for DNA comparison. The isotopic compositions of various body tissues have been demonstrated to be useful biomarkers for tracking locations and movements to aid in the identification of human remains. This study closes the large spatial gap of available 87Sr/86Sr ratios from North America in tap water and presents the first 87Sr/86Sr human tissue-based ratios from Mexico. The 101 hair samples from 32 locations in Mexico range in 87Sr/86Sr ratios from 0.70424 to 0.71613 (ΔSrmax–min = 0.01189). Furthermore, 151 tap water samples from 51 locations range between 0.70404 to 0.71385 (ΔSrmax–min = 0.00981). Overall, small variations in the hair and tap water samples collected from individual locations were recorded (ΔSrmax–min = 0.00041 and 0.00034 respectively). Despite the fact that Mexico is one of the largest bottled water consumers in the world, the 87Sr/86Sr ratios of human hair and tap water correlated strongly (R2 = 0.87 for location averages and R2 = 0.80 when using individual data points). These data represent a valuable resource for identifying the provenance of human remains