The Effect of Fuel Consumption on Cylinder Temperatures and Performance of a Cowled Wright J-5 Engine

Given here are the results of tests made to determine the effect of fuel consumption on the cylinder temperatures and the performance of a cowled Wright J-5 engine. The results of these tests indicate that enriching the mixture by increasing the carburetor size results in a reduction in cylinder head and barrel temperatures. The cylinders shielded by the magnetos or the points on the cylinder that do not receive a free flow of cooling air increase most rapidly in temperature as the mixture is leaned. A free flow of air past the cylinders is essential for satisfactory operation on a lean mixture. The results of these tests show that the Wright J-5 engine can withstand severe temperatures for short periods of operation. The test results also show to what extent destructive temperatures may be avoided by enriching the mixture

A Method for Reducing the Temperature of Exhaust Manifolds

This report describes tests conducted at the Langley Memorial Aeronautical Laboratory on an "air-inducting" exhaust manifold for aircraft engines. The exhaust gases from each cylinder port are discharged into the throat of an exhaust pipe which has a frontal bellmouth. Cooling air is drawn into the pipe, where it surrounds and mixes with the exhaust gases. Temperatures of the manifold shell and of the exhaust gases were obtained in flight for both a conventional manifold and the air-inducting manifold. The air-inducting manifold was installed on an engine which was placed on a test stand. Different fuels were sprayed on and into the manifold to determine whether the use of this manifold reduced the fire hazard. The flight tests showed reductions in manifold temperatures of several hundred degrees, to values below the ignition point of aviation gasoline. On the test stand when the engine was run at idling speeds fuels sprayed into the manifold ignited. It is believed that at low engine speeds the fuel remained in the manifold long enough to become thoroughly heated, and was then ignited by the exhaust gas which had not mixed with cooling air. The use of the air-inducting exhaust manifold must reduce the fire hazard by virtue of its lower operating temperature, but it is not a completely satisfactory solution of the problem

Comparative Performance of a Powerplus Vane-type Supercharger and an N.A.C.A. Roots-type Supercharger

This report presents the results of tests of a Power plus supercharger and a comparison of its performance with the performance previously obtained with an N.A.C.A. Roots-type supercharger. The Powerplus supercharger is a positive displacement blower of the vane type having mechanically operated vanes, the movement of which is controlled by slots and eccentrics. The supercharger was tested at a range of pressure differences from 0 to 15 inches of mercury and at speeds from 500 to 2,500 r.p.m. The pressure difference across the supercharger was obtained by throttling the intake of a depression tank which was interposed in the air duct between the supercharger and the Durley orifice box used for measuring the air. The results of these tests show that at low pressure differences and at all speeds the power required by the Powerplus supercharger to compress a definite quantity of air per second is considerably higher than that required by the Roots. At pressure differences from 10 to 14 inches of mercury and at speeds over 2,000 r.p.m. the power requirements of the two superchargers are practically the same. At a pressure difference of 15 inches of mercury or greater and at a speed of 2,500 r.p.m. or greater the performance of the Powerplus supercharger is slightly better than that of the Roots. Because the Powerplus supercharger cannot be operated at a speed greater than 3,000 r.p.m. as compared with 7,000 r.p.m. for the Roots, its capacity is approximately one-half that of the Roots for the same bulk. The Powerplus supercharger is more complicated and less reliable than the Roots supercharger

Heat Dissipation from a Finned Cylinder at Different Fin-Plane/Air-stream Angles

This report gives the results of an experimental determination of the temperature distribution in and the heat dissipation from a cylindrical finned surface for various fin-plane/air-stream angles. A steel cylinder 4.5 inches in diameter having slightly tapered fins of 0.30-inch pitch and 0.6 -inch width was equipped with an electrical heating unit furnishing 13 to 248 B.T.U. per hour per square inch of inside wall area. Air at speeds form 30 to 150 miles per hour was directed at seven different angles from 0 degrees to 90 degrees with respect to the fin planes. The tests show the best angle for cooling at all air speeds to be about 45 degrees. With the same temperature for the two conditions and with an air speed of 76 miles per hour, the heat input to the cylinder can be increased 50 percent at 45 degrees fin-plane/air-stream angle over that at 0 degrees

Comparative Performance Obtained with XF7C-1 Airplane Using Several Different Engine Cowlings

Discussed here are problems with the use of cowlings with radial air cooled engines. An XF7C-1 airplane, equipped with service cowling and with narrow ring, wide ring, and exhaust collector ring cowlings over the service cowling, was used. For these four cowling conditions, the rate of climb and high speed performance were determined, the cylinder conditions were measured, and pictures to show visibility were taken. The level flight performance obtained with an engine speed of 1900 r.p.m. for the service type, the narrow ring, the wide ring, and the exhaust collector ring was 144.4, 146.6, 152.8, and 155 mph, respectively. The rate of climb was practically the same for each type tested. The visibility was not materially impaired by the use of the wide or the narrow cowlings. With the narrow ring and exhaust collector ring cowlings there was an increase in cylinder temperature. However, this increase was not enough to affect the performance of the engine. The use of an exhaust collector ring incorporated into the cowling is practical where the problem of visibility does not enter

Magnetic Susceptibility: Further Insights into Macroscopic and Microscopic Fields and the Sphere of Lorentz

To make certain quantitative interpretations of spectra from NMR experiments carried out on heterogeneous samples, such as cells and tissues, we must be able to estimate the magnetic and electric fields experienced by the resonant nuclei of atoms in the sample. Here, we analyze the relationships between these fields and the fields obtained by solving the Maxwell equations that describe the bulk properties of the materials present. This analysis separates the contribution to these fields of the molecule in which the atom in question is bonded, the "host" fields, from the contribution of all the other molecules in the system, the "external" fields. We discuss the circumstances under which the latter can be found by determining the macroscopic fields in the sample and then removing the averaged contribution of the host molecule. We demonstrate that the results produced by the, so-called, "sphere of Lorentz" construction are of general validity in both static and time-varying cases. This analytic construct, however, is not "mystical" and its justification rests not on any sphericity in the system but on the local uniformity and isotropy, i.e., spherical symmetry, of the medium when averaged over random microscopic configurations. This local averaging is precisely that which defines the equations that describe the macroscopic fields. Hence, the external microscopic fields, in a suitably averaged sense, can be estimated from the macroscopic fields. We then discuss the calculation of the external fields and that of the resonant nucleus in NMR experiments.Comment: 21 pages, 8 figures, v2: updated to resemble the published versio

Tyrosine/Cysteine Cluster Sensitizing Human γD-Crystallin to Ultraviolet Radiation-Induced Photoaggregation in Vitro

Ultraviolet radiation (UVR) exposure is a major risk factor for age-related cataract, a protein-aggregation disease of the human lens often involving the major proteins of the lens, the crystallins. γD-Crystallin (HγD-Crys) is abundant in the nucleus of the human lens, and its folding and aggregation have been extensively studied. Previous work showed that HγD-Crys photoaggregates in vitro upon exposure to UVA/UVB light and that its conserved tryptophans are not required for aggregation. Surprisingly, the tryptophan residues play a photoprotective role because of a distinctive energy-transfer mechanism. HγD-Crys also contains 14 tyrosine residues, 12 of which are organized as six pairs. We investigated the role of the tyrosines of HγD-Crys by replacing pairs with alanines and monitoring photoaggregation using light scattering and SDS-PAGE. Mutating both tyrosines in the Y16/Y28 pair to alanine slowed the formation of light-scattering aggregates. Further mutant studies implicated Y16 as important for photoaggregation. Mass spectrometry revealed that C18, in contact with Y16, is heavily oxidized during UVR exposure. Analysis of multiple mutant proteins by mass spectrometry suggested that Y16 and C18 likely participate in the same photochemical process. The data suggest an initial photoaggregation pathway for HγD-Crys in which excited-state Y16 interacts with C18, initiating radical polymerization.National Eye Institute (EY015834

Yale School of Public Health Symposium on tissue imaging mass spectrometry: illuminating phenotypic heterogeneity and drug disposition at the molecular level.

‘A picture is worth a thousand words’ is an idiom from the English language (‘borrowed’ from on old Chinese proverb) that conveys the notion that a complex idea can be succinctly and fully described by a single image. Never has this expression been truer than in the clinical and pharmaceutical arenas. Enormous strides have been made by the scientific community in the evolving field of biomedical imaging with the aim of representing and/or quantifying aspects of disease and drug action by using tools such as radiography, MRI, PET, and ultrasound. Yet linking the phenotypical data generated by these systems to the genome is a challenging task. Identifying the link between the mechanism of disease or failed drug response to the genome of an individual is difficult, because central pieces of information are missing. However, imaging mass spectrometry (IMS) can overcome this issue. IMS aims to detect the molecular constituents of the tissue; these can then be correlated with genome-related characteristics, such as gene expression patterns and possible mutations, and ultimately provide a phenotypic molecular link to the complex disease biology. The big data technology of IMS can generate spatial information of thousands of metabolites and proteins from within a tissue, facilitating a deeper understanding of the connections between the genome, phenotypic characteristics and the biological response. It is a technology that has the potential to serve as a segue between gene expression and observed biological signal

A case of eosinophilic esophagitis discovered with positron emission tomography imaging: a case report

INTRODUCTION: Eosinophilic esophagitis was first reported in 1978, and since then it has been increasingly recognized as one of the major etiologies for dysphagia, food impaction, and food regurgitation. To the best of our knowledge, no case of eosinophilic esophagitis (excluding esophageal eosinophilia not responsive to proton pump inhibitor treatment) has previously been demonstrated on the basis of positron emission tomography imaging. CASE PRESENTATION: A 68-year-old Caucasian man presented with dysphagia to solids with recurrent regurgitation and weight loss of 7lb within the preceding 2 months. The patient attributed these symptoms to radiation therapy he had received 1 year earlier for squamous cell cancer of the lung. The patient underwent routine follow-up positron emission tomography imaging, which showed a hypermetabolic lesion in the posterior mediastinum and was increased at the level of the midesophagus. CONCLUSION: To the best of our knowledge, this is the first reported case of eosinophilic esophagitis demonstrated by positron emission tomography imaging and confirmed with endoscopic evaluation and biopsies both after positron emission tomography imaging and a trial of proton pump inhibitor therapy. This could have an impact on the diagnostic evaluation of esophageal eosinophilic inflammation as well as eosinophilic infiltration of other gastrointestinal organs

DFM synthesis approach based on product-process interface modelling. Application to the peen forming process.

Engineering design approach are curently CAD-centred design process. Manufacturing information is selected and assessed very late in the design process and above all as a reactive task instead of being proactive to lead the design choices. DFM appraoches are therefore assesment methods that compare several design alternatives and not real design approaches at all. Main added value of this research work concerns the use of a product-process interface model to jointly manage both the product and the manufacturing data in a proactive DFM way. The DFM synthesis approach and the interface model are presented via the description of the DFM software platform