Effect of heating rate on gas emissions and properties of fired clay bricks and fired clay bricks incorporated with cigarette butts

In general, the firing process of clay bricks generates a range of gas emissions into the atmosphere. At high concentrations, these volatile emissions can be a serious source of environmental pollutions. The main purpose of this study was to evaluate the effect of different heating rates on gas emissions and properties during the firing of clay bricks and clay bricks incorporated with cigarette butts (CBs). In this investigation, four different heating rates were used: 0.7 °C min−1−1, 2 °C min−1, 5 °C min−1 and 10 °C min. The samples were fired in solid form from room temperature to 1050 °C. During the firing cycles, carbon monoxide, carbon dioxide, nitrogen oxides,hydrogen cyanide and chlorine emissions were measured at different heating rates. All bricks were also tested for their physical and mechanical properties including dry density, compressive strength, tensile strength, water absorption and initial rate of absorption. Results show that gas emissions were reduced significantly with higher heating rates (10 °C min) followed by 5 °C min−1−1 and 2 °C min for both types of brick samples. Higher heating rates also decrease the compressive strength and tensile strength value but demonstrate an insignificant effect on the water absorption properties respectively. In conclusion, a higher heating rate is preferable in terms of decreasing gas emissions and it is also able to produce adequate physical and mechanical properties especially for the CB brick

Productivity in the Forest Products Sector: A Review of the Literature

The present literature review is an attempt to gather and summarize the extent of our knowledge of the productivity trends and levels in the forest products sector. We consider single factor as well as total factor productivity definitions. The studies ?from around the world but mainly focusing on the Canadian and American forest product industries ?have been regrouped in sections: (1) general, (2) logging, (3) saw milling, lumber and wood products, and (4) pulp and paper studies.The report also synthesizes the findings of the studies along two lines: (1) the overall productivity growth trends in Canada and other countries and a comparison between forest products sectors in Canada and the United States; and (2) the determinants of productivity growth.Forestry, Forest Products, Logging, Wood Products, Primary Manufacturing, Primary Industries, Pulp and Paper, Paper Products, Forestry Industry, Canada, United States, Productivity, Productivity Growth

Challenges in the Analysis of Historic Concrete:Understanding the Limitations of Techniques, the Variability of the Material and the Importance of Representative Samples

The number of historically-significant concrete structures which require conservation and repair is ever-increasing. The use of unsuitable proprietary materials has led to poor quality repairs of historically-significant structures in the United Kingdom, some of which have resulted in damage to the historic character of the structure and accelerated deterioration of the substrate. As a result, the approach to the repair of historic concrete structures has shifted from the use of mass-produced proprietary repair materials to purpose-made ‘like-for-like’ replacements which, theoretically, have similar mechanical and aesthetic properties. In order to create like-for-like repair materials, the original mix proportions and water/cement (w/c) ratio of the substrate have to be established. However, there are concerns regarding the accuracy of existing techniques and standards used for the analyses of hardened concrete. Furthermore, due to a lack of available material, analyses are often carried out on samples that are much smaller than the minimum requirement for a representative sample, or from areas which are not representative. This paper discusses these issues and hopes to provide information to conservators and analysts on the limitations of techniques, the variability of the material and the importance of representative samples

Modelling and optimisation of design of non-conventional instrument transformers

In this paper, we have proposed, modelled and optimised several designs of non-conventional instrument transformer (NCIT) for high voltage overhead transmission lines (400kV). We have discussed several parameters and investigated how they influence the sensitivity of our NCIT, consisting of magnetic shape memory (MSM) element, magnetic circuit and an LVDT (linear variable differential transformer). One of the most used conductors in these lines, 528-Al1/69-ST1A ACSR conductor (old code MOOSE), was modelled together with the MSM element and the magnetic circuit in ANSYS APDL. Based on the obtained results we have given suggestions on how NCIT could be designed taking into account a choice of the most appropriate material for this application. The way how the model was developed was presented as well as calculations of errors in the model in ANSYS APDL for electromagnetic problems

Neutrality of narrative discussion in annual reports of UK listed companies

This paper reports the results of an investigation into the neutrality of the narrative discussion of financial performance and position, as evidenced in 179 annual reports of UK listed companies. Neutrality of narrative discussion was determined by comparing the average proportions of good and bad news contained in the narrative and statutory accounts sections of the annual reports. The results of a comparison of the proportion of good news in the two sections of the annual reports suggest that the narrative sections contained a significantly higher proportion of good news than the statutory accounts sections. Comparison of proportions of bad news, however, indicates that the narrative sections contained a significantly lower proportion of bad news compared to the statutory accounts sections. Finally, the results also suggest that the proportion of good news as compared to bad news in the narrative sections is significantly higher than the proportion of good news compared to bad news in the statutory accounts section. The results are consistent with the suggestion that company management highlights good news in narrative discussions. The implications of the findings for company management, users, auditors and regulators are discussed

Thermal, mechanical and microstructural analysis of concrete containing microencapsulated phase change materials

This paper studies the thermal, mechanical and microstructural aspects of concrete containing different amounts of microencapsulated phase change materials (PCMs). In addition, numerical simulation is carried out to study the potential application of PCM-modified concrete for reduction in summer surface temperature. It is shown that increasing PCM content in concrete led to lower thermal conductivity and an increase in the heat storage ability of concrete. However, the compressive and flexural strength of concrete significantly decreased. Microstructural analysis showed that PCMs appear to remain intact during mixing; however, PCM particles appear to fail by bursting under loading, creating hemispherical voids and crack initiation points as well as possible entrapped air behaviour. The result of numerical simulation revealed that reduction in summer concrete pavement surface temperature by several degrees was possible, with implications for reduction in concrete thermal stresses, shrinkage and urban heat island effect

Biodegradability standards for carrier bags and plastic films in aquatic environments: a critical review

Plastic litter is encountered in aquatic ecosystems across the globe, including polar environments and the deep sea. To mitigate the adverse societal and ecological impacts of this waste, there has been debate on whether ‘biodegradable’ materials should be granted exemptions from plastic bag bans and levies. However, great care must be exercised when attempting to define this term, due to the broad and complex range of physical and chemical conditions encountered within natural ecosystems. Here, we review existing international industry standards and regional test methods for evaluating the biodegradability of plastics within aquatic environments (wastewater, unmanaged freshwater and marine habitats). We argue that current standards and test methods are insufficient in their ability to realistically predict the biodegradability of carrier bags in these environments, due to several shortcomings in experimental procedures and a paucity of information in the scientific literature. Moreover, existing biodegradability standards and test methods for aquatic environments do not involve toxicity testing or account for the potentially adverse ecological impacts of carrier bags, plastic additives, polymer degradation products or small (microscopic) plastic particles that can arise via fragmentation. Successfully addressing these knowledge gaps is a key requirement for developing new biodegradability standard(s) for lightweight carrier bags

Quality Standards for the Development, Application, and Evaluation of Measurement Instruments in Social Science Survey Research

[Introduction] Since its establishment in 2004, the German Data Forum (RatSWD), which is funded by the German Federal Ministry of Science and Research (BMBF), has been advising the federal government and the governments of the federal states (Länder) on issues relating to the expansion and improvement of the research infrastructure for the empirical social, behavioral, and economic sciences (SBE). In late 2010, the RatSWD addressed the question of how the quality of survey instruments in the social and economic sciences, and especially in social and economic survey research, could be controlled and assured. At a meeting on November 9, 2012, the RatSWD therefore decided to set up a 'Quality Assurance of Survey Instruments Working Group' under the leadership of Professor Beatrice Rammstedt. The establishment of the working group was prompted in particular by the desire to define quality standards in order to assure and optimize the quality of survey instruments. Hence, the working group made the formulation of these standards its primary objective. They are presented in this paper

The upgrading of fire safety in historic buildings

There is a seemingly continual erosion of our cultural heritage due to fires in historic buildings. Some of these fires result in partial loss of the asset, some result in total loss – in all cases irreplaceable historic fabric is destroyed. Accurate recording for fires in historic buildings is problematic, but such data as has been collated indicates that the level of loss is high. One of the key factors in achieving robust fire safety in historic buildings is the upgrading of physical fire protection measures. It has been suggested that we should assume a fire event is probable, and together with a context in which outside help might be some time in arriving, such measures are considered crucial in containing the fire and raising the alarm as quickly as possible. This article considers passive and active fire protection measures, using case study material to provide illustrative examples. Where it might be expected that conservation requirements, aiming to avoid negative impact to character and significance, might hinder disruptive physical interventions to improve fire protection, in fact a great deal can be achieved. Such a pragmatic approach is arguably necessary for the safety and preservation of built heritage, when the alternative might otherwise be yet another burnt-out shell