Flow boiling heat transfer of refrigerant R-134a in copper microchannel heat sink

This paper was presented at the 4th Micro and Nano Flows Conference (MNF2014), which was held at University College, London, UK. The conference was organised by Brunel University and supported by the Italian Union of Thermofluiddynamics, IPEM, the Process Intensification Network, the Institution of Mechanical Engineers, the Heat Transfer Society, HEXAG - the Heat Exchange Action Group, and the Energy Institute, ASME Press, LCN London Centre for Nanotechnology, UCL University College London, UCL Engineering, the International NanoScience Community, www.nanopaprika.eu.In this paper we present experimental data on heat transfer and pressure drop characteristics at flow boiling of refrigerant R-134a in a horizontal microchannel heat sink. The primary objective of this study is to establish experimentally how the local heat transfer coefficient and pressure drop correlate with the heat flux, mass flux and vapor quality. The copper plate of microchannel heat sink contains 21 microchannels with 335x930 m2 cross-section. The microchannel plate and heating block were divided by the partition wall for the local heat flux measurements. Distribution of local heat transfer coefficients along the length and width of the microchannel plate were measured in the range of external heat fluxes from 50 to 500 kW/m2; the mass flux was varied within 200-600 kg/m2s, and pressure was varied within 6-16 bar. The obvious impact of heat flux on the magnitude of heat transfer coefficient was observed. It shows that nucleate boiling is the dominant mechanism for heat transfer. The new model of flow boiling heat transfer, which accounts nucleate boiling suppression and liquid film evaporation, was proposed and verified experimentally in this paper

Explosive Vaporization of Water and Isopropyl Alcohol on a Flat Microheater

This paper was presented at the 4th Micro and Nano Flows Conference (MNF2014), which was held at University College, London, UK. The conference was organised by Brunel University and supported by the Italian Union of Thermofluiddynamics, IPEM, the Process Intensification Network, the Institution of Mechanical Engineers, the Heat Transfer Society, HEXAG - the Heat Exchange Action Group, and the Energy Institute, ASME Press, LCN London Centre for Nanotechnology, UCL University College London, UCL Engineering, the International NanoScience Community, www.nanopaprika.eu.The MEMS control systems, such as ink jet printers, optical switches and valves, use the explosive vaporization of metastable liquid for the rapid phase change. The initial stage of explosive vaporization of water, isopropyl alcohol and ethanol has been studied experimentally on the surface of a thin-film microheater, covered with the submicron silicon-carbide layer. In experiments, the multilayer thin-film resistor of the Think Jet printhead with 100 × 110 μm2 surface area was used. Applying the optical method, we investigated the patterns of the liquid–vapor phase transition under pulse heating and obtained the characteristics of nucleation at the rate of temperature growth of up to 800 MK/s. Pulsed laser illumination was applied for the high-speed photography of liquid vaporization. Data for the vapor-covered surface area vs. time depending on the supplied heat flux and the heating time are reported. The theoretical model of explosive vaporization on a flat heater has been developed and numerical simulations have been performed for water and isopropyl alcohol nucleation on the multi-layer microheater. Comparison of calculation results with experimental data is discussed in this paper

Glass-fiber woven catalysts as alternative catalytic materials for various industries. A review

The chemistry and technology of new versatile multipurpose catalytic systems developed and studied by the authors for the purposes of heterogeneous catalysis are reviewed. A theoretical background for a successful search for these new catalytic systems is based on an unconventional approach with emphasis on an essential role of branched-chain reaction mechanisms of heterogeneous catalysis previously developed by the authoring team. The catalytic systems under study are based on silica (aluminoborosilicate) glass-fiber amorphous matrices doped with various metals and manufactured as articles with various types of woven structure. The specific features of these glass-fiber woven catalytic systems, such as their structure, phase state of the matrix, manufacture and activation methods, design of catalytic reactors in which they operate, as well as production technologies and operation methods, make a compelling case to regard them as a new separate class of catalysts. As compared to conventional catalytic materials, these new catalysts are highly efficient in neutralizing industrial gas emissions, in contact stages of the production of nitric acid and sulfuric acid, in various reactions of catalytic hydrocarbon processing, in water purification from nitrate and nitrite contaminants, in catalytic heat generation, etc

Rapidity and Centrality Dependence of Proton and Anti-proton Production from Au+Au Collisions at sqrt(sNN) = 130GeV

We report on the rapidity and centrality dependence of proton and anti-proton transverse mass distributions from Au+Au collisions at sqrt(sNN) = 130GeV as measured by the STAR experiment at RHIC. Our results are from the rapidity and transverse momentum range of |y|<0.5 and 0.35 <p_t<1.00GeV/c. For both protons and anti-protons, transverse mass distributions become more convex from peripheral to central collisions demonstrating characteristics of collective expansion. The measured rapidity distributions and the mean transverse momenta versus rapidity are flat within |y|<0.5. Comparisons of our data with results from model calculations indicate that in order to obtain a consistent picture of the proton(anti-proton) yields and transverse mass distributions the possibility of pre-hadronic collective expansion may have to be taken into account.Comment: 4 pages, 3 figures, 1 table, submitted to PR

Ratio of the Isolated Photon Cross Sections at \sqrt{s} = 630 and 1800 GeV

The inclusive cross section for production of isolated photons has been measured in \pbarp collisions at $\sqrt{s} = 630$ GeV with the \D0 detector at the Fermilab Tevatron Collider. The photons span a transverse energy ($E_T$) range from 7-49 GeV and have pseudorapidity $|\eta| < 2.5$. This measurement is combined with to previous \D0 result at $\sqrt{s} = 1800$ GeV to form a ratio of the cross sections. Comparison of next-to-leading order QCD with the measured cross section at 630 GeV and ratio of cross sections show satisfactory agreement in most of the $E_T$ range.Comment: 7 pages. Published in Phys. Rev. Lett. 87, 251805, (2001

Performance of the CMS Cathode Strip Chambers with Cosmic Rays

The Cathode Strip Chambers (CSCs) constitute the primary muon tracking device in the CMS endcaps. Their performance has been evaluated using data taken during a cosmic ray run in fall 2008. Measured noise levels are low, with the number of noisy channels well below 1%. Coordinate resolution was measured for all types of chambers, and fall in the range 47 microns to 243 microns. The efficiencies for local charged track triggers, for hit and for segments reconstruction were measured, and are above 99%. The timing resolution per layer is approximately 5 ns

Azimuthal anisotropy and correlations at large transverse momenta in p+pp+p and Au+Au collisions at sNN\sqrt{s_{_{NN}}}= 200 GeV

Results on high transverse momentum charged particle emission with respect to the reaction plane are presented for Au+Au collisions at $\sqrt{s_{_{NN}}}$= 200 GeV. Two- and four-particle correlations results are presented as well as a comparison of azimuthal correlations in Au+Au collisions to those in $p+p$ at the same energy. Elliptic anisotropy, $v_2$, is found to reach its maximum at $p_t \sim 3$ GeV/c, then decrease slowly and remain significant up to $p_t\approx 7$ -- 10 GeV/c. Stronger suppression is found in the back-to-back high-$p_t$ particle correlations for particles emitted out-of-plane compared to those emitted in-plane. The centrality dependence of $v_2$ at intermediate $p_t$ is compared to simple models based on jet quenching.Comment: 4 figures. Published version as PRL 93, 252301 (2004

Multi-length scale 5D diffraction imaging of Ni-Pd/CeO2-ZrO2/Al2O3 catalyst during partial oxidation of methane

A 5D diffraction imaging experiment (with 3D spatial, 1D time/imposed operating conditions and 1D scattering signal) was performed with a Ni–Pd/CeO2–ZrO2/Al2O3 catalyst. The catalyst was investigated during both activation and partial oxidation of methane (POX). The spatio-temporal resolved diffraction data allowed us to obtain unprecedented insight into the behaviour and fate of the various metal and metal oxide species and how this is affected by the heterogeneity across catalyst particles. We show firstly, how Pd promotion although facilitating Ni reduction, over time leads to formation of unstable Ni–Pd metallic alloy, rendering the impact of Pd beyond the initial reduction less important. Furthermore, in the core of the particles, where the metallic Ni is primarily supported on Al2O3, poor resistance towards coke deposition was observed. We identified that this preceded via the formation of an active yet metastable interstitial solid solution of Ni–C and led to the exclusive formation of graphitic carbon, the only polymorph of coke observed. In contrast, at the outermost part of the catalyst particle, where Ni is predominantly supported on CeO2–ZrO2, the graphite formation was mitigated but sintering of Ni crystallites was more severe

Azimuthal anisotropy in Au+Au collisions at sqrtsNN = 200 GeV

The results from the STAR Collaboration on directed flow (v_1), elliptic flow (v_2), and the fourth harmonic (v_4) in the anisotropic azimuthal distribution of particles from Au+Au collisions at sqrtsNN = 200 GeV are summarized and compared with results from other experiments and theoretical models. Results for identified particles are presented and fit with a Blast Wave model. Different anisotropic flow analysis methods are compared and nonflow effects are extracted from the data. For v_2, scaling with the number of constituent quarks and parton coalescence is discussed. For v_4, scaling with v_2^2 and quark coalescence is discussed.Comment: 26 pages. As accepted by Phys. Rev. C. Text rearranged, figures modified, but data the same. However, in Fig. 35 the hydro calculations are corrected in this version. The data tables are available at http://www.star.bnl.gov/central/publications/ by searching for "flow" and then this pape

Two-dimensional elastoplastic analysis of cylindrical cavity problems in Tresca materials

This paper presents analytical elastic-plastic solutions for static stress loading analysis and quasi-static expansion analysis of a cylindrical cavity in Tresca materials, considering biaxial far-field stresses and shear stresses along the inner cavity wall. The two-dimensional static stress solution is obtained by assuming that the plastic zone is statically determinate and using the complex variable theory in the elastic analysis. A rigorous conformal mapping function is constructed, which predicts that the elastic-plastic boundary is in an elliptic shape under biaxial in situ stresses, and the range of the plastic zone extends with increasing internal shear stresses. The major axis of the elliptical elastic-plastic boundary coincides with the direction of the maximum far-field compression stress. Furthermore, considering the internal shear stresses, an analytical large-strain displacement solution is derived for continuous cavity expansion analysis in a hydrostatic initial stress filed. Based on the derived analytical stress and displacement solutions, the influence of the internal shear stresses on the quasi-static cavity expansion process is studied. It is shown that additional shear stresses could reduce the required normal expansion pressure to a certain degree, which partly explains the great reduction of the axial soil resistance due to rotations in rotating cone penetration tests. In addition, through additionally considering the potential influences of biaxial in situ stresses and shear stresses generated around the borehole during drillings, an improved cavity expansion approach for estimating the maximum allowable mud pressure of horizontal directional drillings (HDDs) in undrained clays is proposed and validated